RV News RVBusiness 2021 Top 10 RVs of the Year, plus 56 additional debuts and must-see units → ×
 

Go Back   Keystone RV Forums > Keystone Fleet | Keystone RV Models > Travel Trailers
Click Here to Login

Reply
 
Thread Tools Display Modes
 
Old 02-21-2020, 09:06 PM   #1
mrt10x
Junior Member
 
Join Date: Feb 2020
Location: Woodland Park
Posts: 4
Outback 210URS Slide Override

I can not find anything in the owners manual, or online for this. Can anyone point me to where the override is for the rear slide is on a 210URS?
__________________

mrt10x is offline   Reply With Quote
Old 02-22-2020, 03:16 AM   #2
chuckster57
Site Team
 
chuckster57's Avatar
 
Join Date: Jul 2014
Location: Modesto
Posts: 12,428
Welcome to the forum!! Iím not familiar with your particular trailer, can you tell me what type of slide it is, Is it cable?
__________________

__________________

2012 Copper Canyon 273FWRET being towed by a 1994 Ford F350 CC,LB,Dually diesel.
Airlift 5000 bags, Prodigy brake control, 5 gauges on the pillar.Used to tow a '97 Jayco 323RKS.

Now an RVIA registered tech. Retired from Law enforcement in 2008 after 25+ yrs.
chuckster57 is offline   Reply With Quote
Old 02-22-2020, 08:34 AM   #3
mrt10x
Junior Member
 
Join Date: Feb 2020
Location: Woodland Park
Posts: 4
Here is a link to the layout.. yes it is cable slide. It is out the back. When I bought it 3 years ago they told me the motor was behind some of the molding inside the camper.. but at the time I wasnt smart enough to get a better explanation.. I just figured it would be in the owners manual.. or I could find an answer on the internet.. .Google fixes everything

https://www.keystonerv.com/travel-tr...ravel-trailer/
mrt10x is offline   Reply With Quote
Old 02-22-2020, 11:25 AM   #4
chuckster57
Site Team
 
chuckster57's Avatar
 
Join Date: Jul 2014
Location: Modesto
Posts: 12,428
If itís cable driven then the motor is above the slide, inside centered. You should have received a flexible shaft with a squarehead driver on the end. The driver end goes into the gearbox at the motor and the hex drive goes into a drill chuck. Operating drill will operate gear box and extend/retract slide. On some models you have to remove the upper slide Facia to access the motor/gearbox.
__________________

2012 Copper Canyon 273FWRET being towed by a 1994 Ford F350 CC,LB,Dually diesel.
Airlift 5000 bags, Prodigy brake control, 5 gauges on the pillar.Used to tow a '97 Jayco 323RKS.

Now an RVIA registered tech. Retired from Law enforcement in 2008 after 25+ yrs.
chuckster57 is offline   Reply With Quote
Old 02-22-2020, 12:26 PM   #5
mrt10x
Junior Member
 
Join Date: Feb 2020
Location: Woodland Park
Posts: 4
Quote:
Originally Posted by chuckster57 View Post
If itís cable driven then the motor is above the slide, inside centered. You should have received a flexible shaft with a squarehead driver on the end. The driver end goes into the gearbox at the motor and the hex drive goes into a drill chuck. Operating drill will operate gear box and extend/retract slide. On some models you have to remove the upper slide Facia to access the motor/gearbox.

I didn't receive the flexible shaft...I think it actually has a jack type turn handle... that is where I thought it was... I guess as the camper gets older I am expecting to need it at some point
mrt10x is offline   Reply With Quote
Old 02-22-2020, 12:31 PM   #6
chuckster57
Site Team
 
chuckster57's Avatar
 
Join Date: Jul 2014
Location: Modesto
Posts: 12,428
Sometimes the flexible shaft tool is taped to the motor/gearbox. If your slide is cable driven, that flexible shaft with the square drive bit or itís equivalent is the only way to override that Iím aware of.
__________________

2012 Copper Canyon 273FWRET being towed by a 1994 Ford F350 CC,LB,Dually diesel.
Airlift 5000 bags, Prodigy brake control, 5 gauges on the pillar.Used to tow a '97 Jayco 323RKS.

Now an RVIA registered tech. Retired from Law enforcement in 2008 after 25+ yrs.
chuckster57 is offline   Reply With Quote
Old 02-22-2020, 02:24 PM   #7
mrt10x
Junior Member
 
Join Date: Feb 2020
Location: Woodland Park
Posts: 4
Quote:
Originally Posted by chuckster57 View Post
Sometimes the flexible shaft tool is taped to the motor/gearbox. If your slide is cable driven, that flexible shaft with the square drive bit or itís equivalent is the only way to override that Iím aware of.
I was sure that it was a hard tool.. but I think I was confusing my old Trailmanor and my new Outback. I did find the tool,, had to walk through two feet of snow to go check In the Spring when I power it back up I will take off the trim below the bed where I think the motor is.
mrt10x is offline   Reply With Quote
Old 02-22-2020, 02:31 PM   #8
flybouy
Site Team
 
Join Date: Oct 2011
Location: Joppa, MD
Posts: 5,413
mrt10x, DW has sister that lives up the road in Divive (actually about 7 miles further up the mountain). Pretty country. He retired from Teller County as a Deputy after retiring from the Army.
__________________
Marshall
2012 Laredo 303 TG
2010 F250 LT Super Cab, long bed, 4X4, 6.4 Turbo Diesel
flybouy is offline   Reply With Quote
Old 02-22-2020, 06:33 PM   #9
Stumpy75
Member
 
Join Date: Mar 2014
Location: Toledo, OH
Posts: 42
My motor is located UNDER the slide, above the top step to the rear slide.... You have to slither on your stomach to get to it if the rear slide is in. I tried getting to it once, and really hope I never really need to do something with it for real. Great engineering... The flexible tool is taped to my motor.
__________________
Chris

2014 Keystone Outback 210TRS
2020 F150, 3.5l, 4x4, 3.55:1, Supercrew
Stumpy75 is offline   Reply With Quote
Old 02-22-2020, 07:02 PM   #10
chuckster57
Site Team
 
chuckster57's Avatar
 
Join Date: Jul 2014
Location: Modesto
Posts: 12,428
Iíve seen it UNDER the slide in very few cases, guess this is one of them.
__________________

__________________

2012 Copper Canyon 273FWRET being towed by a 1994 Ford F350 CC,LB,Dually diesel.
Airlift 5000 bags, Prodigy brake control, 5 gauges on the pillar.Used to tow a '97 Jayco 323RKS.

Now an RVIA registered tech. Retired from Law enforcement in 2008 after 25+ yrs.
chuckster57 is offline   Reply With Quote
Reply

Tags
outback, slide

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Powered by vBadvanced CMPS v3.2.3
Disclaimer:

This website is not affiliated with or endorsed by the Keystone RV Company or any of its affiliates in any way. Keystone RVģ is a registered trademark of the Keystone RV Company.


All times are GMT -8. The time now is 07:56 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
×