|
|
04-16-2015, 05:28 PM
|
#1
|
Senior Member
Join Date: May 2010
Location: Rochester, NY
Posts: 1,605
|
Wobble Table (Pedestal Base Style)
So I have searched this forum and the internet and can not seem to find a economical solution to my wobbly dining table. The table has two surface mount bases and legs like these: http://www.pplmotorhomes.com/parts/r...stal-table.htm
I have tried every thing. The bases are tight into the floor. I have trier reshaping the tapered ends of the legs to help ensure a tighter fit into the top and bottom bases. No AVAIL. I can not mount the end of the table to the wall as the window extends well below the table top.
Are there higher quality bases/legs than what comes from the factory?
I found these: http://www.campingworld.com/shopping...4ujxoCexDw_wcB
Are they any good. Any insight into replacing the junk pedestals I have is appreciated.
|
|
|
04-16-2015, 06:58 PM
|
#2
|
Senior Member
Join Date: Aug 2012
Location: Brant Lake,NY
Posts: 321
|
When I had a TT and the table was wobbly I replace them with Marine table legs they are Straight not tapered. Plus they had a clip to hold and release them.
__________________
Gary & Gail
Alfa Gold 3905SH
2016 F350 DWD 4X4 6.7,3.73 Rear
2012 Cougar 318SAB
2015 F350 SWD 4X4 3.55 Rear
|
|
|
04-16-2015, 07:52 PM
|
#3
|
Senior Member
Join Date: Apr 2013
Location: Green Valley, AZ
Posts: 782
|
There is another easy solution if you don't often have to put the table down into the sleeping position. Just drill a small hole through the base and leg and then turn a sheet metal screw into the hole. That will hold it rock solid. I did that on a former table that gave me fits and it worked like a charm.
__________________
Earl
2007 33.5' Arctic Fox Fifth Wheel used for full-timing for several years--now sold
2011 Hideout 23RKSWE that we now use for poking around local parks
2007 Chevy 3/4 ton diesel with Prodigy Brake Control
|
|
|
04-18-2015, 07:50 AM
|
#4
|
Senior Member
Join Date: Nov 2013
Location: Southwest Wyoming
Posts: 497
|
We just ordered the Springfield three-stage table pedestal. It will be here in a couple of days, and we'll let you know what we think. Another forum member replaced the two posts with this. He said it's very solid, increases leg room vastly and can easily be lowered to bed height. We'll see! Our concern was not wobble - it was the leg room.
__________________
2017 Jayco Melbourne 24k-Jeep Wrangler
2013 Bullet Premier 19FBPR-Dodge Durango V8 Hemi
2013 Rpod 177HRE-Jeep Liberty
2011 Aliner Sport-Jeep Cherokee
2008 Little Guy 5^Wide-Toyota Avalon
1980 Shasta 21-GMC Suburban
1981 Coleman Tent Camper-1981 Dodge Ramcharger
1978 VW Westfalia
Lots of tents
|
|
|
04-18-2015, 04:28 PM
|
#5
|
Senior Member
Join Date: May 2010
Location: Rochester, NY
Posts: 1,605
|
Quote:
Originally Posted by koko
We just ordered the Springfield three-stage table pedestal. It will be here in a couple of days, and we'll let you know what we think. Another forum member replaced the two posts with this. He said it's very solid, increases leg room vastly and can easily be lowered to bed height. We'll see! Our concern was not wobble - it was the leg room.
|
Please let me know how it works out. Thanks
Steve
|
|
|
04-18-2015, 04:55 PM
|
#6
|
Site Team
Join Date: Jul 2014
Location: Modesto
Posts: 20,350
|
The three stage pedestal is used in some high end class A's and it's solid.
__________________
2012 Copper Canyon 273FWRET being towed by a 1994 Ford F350 CC,LB,Dually diesel.
Airlift 5000 bags, Prodigy brake control, 5 gauges on the pillar.Used to tow a '97 Jayco 323RKS.
Now an RVIA registered tech. Retired from Law enforcement in 2008 after 25+ yrs.
|
|
|
04-18-2015, 05:24 PM
|
#7
|
Senior Member
Join Date: May 2010
Location: Rochester, NY
Posts: 1,605
|
I checked it out. Looks very nice and sure it will work, but OMG $$$.
I think I will have to resort to another measure for my wobbliness.
|
|
|
04-19-2015, 07:22 AM
|
#8
|
Senior Member
Join Date: Nov 2013
Location: Southwest Wyoming
Posts: 497
|
Quite pricey, so we'll make sure it's going to be PERFECT before we actually install it. If it works, it will be worth every penny. We spend a lot of time in our trailer and like to gather family around our table.
__________________
2017 Jayco Melbourne 24k-Jeep Wrangler
2013 Bullet Premier 19FBPR-Dodge Durango V8 Hemi
2013 Rpod 177HRE-Jeep Liberty
2011 Aliner Sport-Jeep Cherokee
2008 Little Guy 5^Wide-Toyota Avalon
1980 Shasta 21-GMC Suburban
1981 Coleman Tent Camper-1981 Dodge Ramcharger
1978 VW Westfalia
Lots of tents
|
|
|
04-20-2015, 02:00 AM
|
#9
|
Member
Join Date: Jun 2013
Location: Winnipeg
Posts: 32
|
Quote:
Originally Posted by theeyres
There is another easy solution if you don't often have to put the table down into the sleeping position. Just drill a small hole through the base and leg and then turn a sheet metal screw into the hole. That will hold it rock solid. I did that on a former table that gave me fits and it worked like a charm.
|
Just wanted to say that I ‘second’ this suggestion. Never thought of ‘it’ myself; wound up replacing the 2-steel post table setup with a very nice ‘Genuine’ OAK Wood RV Extensible table that I found on Kijiji for $75.00. MUCH BETTER and NICER/NICER LOOKING and with a BIGGER TABLE SURFACE AREA as well.
Couple of thoughts:
1. Instead in ‘screws’, you MIGHT consider TAPPING the ‘pole recipient fixtures’ to ‘take’ either a threaded thumb screw or even small hex head bolts, and maybe using 2 of them at 90 degrees to each other. The former could be tightened/loosened by hand. Two at right angles should provide a lot of stability and in either case, might be easier to remove/reinstall if necessary.
2. In the end, you might still notice a bit of ‘flex’ in the table as the FLOOR that it is bolted to may be both (e.g.) on/through a carpet AND the underlying wood floor material is only maybe 5/8” thick and THAT will ‘give’ a bit if one pushes on a side or end of the table. STILL it should be much better than it is right now.
Again, suggest you try the ‘screw trick’. VERY CHEAP and easy to TRY and if it doesn’t work out, no big deal.
|
|
|
04-20-2015, 07:49 AM
|
#10
|
Senior Member
Join Date: Oct 2013
Location: Huntington Beach, Ca
Posts: 250
|
__________________
2013 Passport 2890RL GT
2015 Silverado CC LTZ 4x 2500 Duramax
HB Cal
|
|
|
04-21-2015, 05:10 PM
|
#11
|
Senior Member
Join Date: Nov 2013
Location: Southwest Wyoming
Posts: 497
|
Received our Springfield Pedestal yesterday and installed it today. It may be pricey; but when you see it, you know why! It makes such a tremendous difference in leg room; and there's no way there could be any wobble. It raises and lowers so smoothly. Cost $318 with tax - free shipping - from Walmart. Personally, it's a small price to pay to solve a huge problem.
__________________
2017 Jayco Melbourne 24k-Jeep Wrangler
2013 Bullet Premier 19FBPR-Dodge Durango V8 Hemi
2013 Rpod 177HRE-Jeep Liberty
2011 Aliner Sport-Jeep Cherokee
2008 Little Guy 5^Wide-Toyota Avalon
1980 Shasta 21-GMC Suburban
1981 Coleman Tent Camper-1981 Dodge Ramcharger
1978 VW Westfalia
Lots of tents
|
|
|
04-26-2015, 06:55 AM
|
#12
|
Member
Join Date: Jul 2014
Location: Niagara Falls, NY
Posts: 79
|
Check out Factory RV Surplus, they have the snap 2 folding table base. You mount your top on it and it folds down to sleeping height. An added bonus is you can take the table outside if you wanted to. They show it for $69.00 with $50.00 shipping on it if that price is better.
Chris
__________________
2019 Jayco Pinnacle 36KPTS
2016 Sierra 3500HD CC,SRW,Diesel,long bed, factory hitch prep
Past:2012 Laredo 335TG, 2003 Cedar Creek 28LRLFS
2003 Flagstaff 25LB,1993 Terry 35V
1982 Serro Scotty 18',1976 Dutchcraft 25'
1972 Banner 18'
|
|
|
04-27-2015, 07:11 AM
|
#13
|
Senior Member
Join Date: May 2010
Location: Rochester, NY
Posts: 1,605
|
Quote:
Originally Posted by Bar-OneRanch
Check out Factory RV Surplus, they have the snap 2 folding table base. You mount your top on it and it folds down to sleeping height. An added bonus is you can take the table outside if you wanted to. They show it for $69.00 with $50.00 shipping on it if that price is better.
Chris
|
Did you buy one? I have seen it but afraid the leg mechanism will take up a lot of leg room.
|
|
|
04-27-2015, 12:39 PM
|
#14
|
Senior Member
Join Date: Apr 2014
Location: Minnesota
Posts: 779
|
Quote:
Originally Posted by therink
Did you buy one? I have seen it but afraid the leg mechanism will take up a lot of leg room.
|
This is what our Cougar X-lite came with for the table base. It does take up a lot of leg room. It hurts like the dickens when you hit a piece of it with your knee or shin (sharp corners/edges), and really doesn't fold and unfold very easily.
This is just my opinion of it, but I'm looking at getting rid of it for a pedestal table base because we can't stand the folding base. I would love the Springfield base, but am still choking over the price...
__________________
--Lynette
2019 F-350 diesel 4x4 CC LB DRW, not the mom taxi anymore...
2021 Alliance Paradigm 340RL
2016 F-350 diesel 4x4 CC LB SRW, mom taxi - sold
2014 Cougar XLite 28RDB - sold
|
|
|
04-28-2015, 05:24 PM
|
#15
|
Member
Join Date: Jul 2014
Location: Niagara Falls, NY
Posts: 79
|
Quote:
Originally Posted by therink
Did you buy one? I have seen it but afraid the leg mechanism will take up a lot of leg room.
|
No I don't have one, I was thinking about getting it when I replaced the cracked floor plates on my Cedar Creek dinette and the replacements were too loose and the table wobbled. Our new trailer has a regular table, I think our friends have it on their new Hornet, we are camping in two weeks and I can check it out and let you know?
Chris
__________________
2019 Jayco Pinnacle 36KPTS
2016 Sierra 3500HD CC,SRW,Diesel,long bed, factory hitch prep
Past:2012 Laredo 335TG, 2003 Cedar Creek 28LRLFS
2003 Flagstaff 25LB,1993 Terry 35V
1982 Serro Scotty 18',1976 Dutchcraft 25'
1972 Banner 18'
|
|
|
04-28-2015, 05:57 PM
|
#16
|
Senior Member
Join Date: May 2010
Location: Rochester, NY
Posts: 1,605
|
Quote:
Originally Posted by Bar-OneRanch
No I don't have one, I was thinking about getting it when I replaced the cracked floor plates on my Cedar Creek dinette and the replacements were too loose and the table wobbled. Our new trailer has a regular table, I think our friends have it on their new Hornet, we are camping in two weeks and I can check it out and let you know?
Chris
|
Cool, thanks
Steve
|
|
|
04-29-2015, 06:40 AM
|
#17
|
Senior Member
Join Date: Apr 2014
Location: Berkley
Posts: 751
|
Springfield pedestal looks nice...I wonder if a slide could be attached to allow the table to slide out a bit to accommodate those against the back wall? I like thought of the pedestal in the middle helping to support of you want to make it into a bed, as opposed to just the tabletop and the small rails on each of the seats. I've already beefed up my rails because the shape of the table can allow it to "slip" past the rails ever so slightly and the table falls through..
__________________
2022 Ford F150 3.5 Ecoboost SCrew 4x4 MaxTow
2020 Salem Hemisphere Hyper-Lyte 25RBHL
|
|
|
04-29-2015, 08:37 AM
|
#18
|
Senior Member
Join Date: Nov 2013
Location: Southwest Wyoming
Posts: 497
|
We've been on a trip for a week now using the new Springfield Pedestal we installed. We are not disappointed. The difference is amazing!
__________________
2017 Jayco Melbourne 24k-Jeep Wrangler
2013 Bullet Premier 19FBPR-Dodge Durango V8 Hemi
2013 Rpod 177HRE-Jeep Liberty
2011 Aliner Sport-Jeep Cherokee
2008 Little Guy 5^Wide-Toyota Avalon
1980 Shasta 21-GMC Suburban
1981 Coleman Tent Camper-1981 Dodge Ramcharger
1978 VW Westfalia
Lots of tents
|
|
|
04-29-2015, 02:36 PM
|
#19
|
Junior Member
Join Date: Jan 2012
Location: New York
Posts: 29
|
Quote:
Originally Posted by {tpc}
Springfield pedestal looks nice...I wonder if a slide could be attached to allow the table to slide out a bit to accommodate those against the back wall? I like thought of the pedestal in the middle helping to support of you want to make it into a bed, as opposed to just the tabletop and the small rails on each of the seats. I've already beefed up my rails because the shape of the table can allow it to "slip" past the rails ever so slightly and the table falls through..
|
This pedestal is a wonderful upgrade. I'm not sure if slide hardware is out there somewhere but, it would make sense. The table does turn easily that gives us easy access to the storage without doing the door/drawer mod. It also let's people get to the rear seat easier. As far as the bed is concerned - rock solid. We highly recommend this mod!
|
|
|
05-01-2015, 04:30 PM
|
#20
|
Senior Member
Join Date: Aug 2014
Location: Tallassee, AL
Posts: 191
|
I had similar setup on the 2005 Outback table. Screws had pulled out of one leg and the other base was worn. I found one folding table leg (like below) to replace one of the pedestal legs. I have no plans to ever use the table as a bed so it doesn't matter if the folding leg doesn't fold completely flat. This photo shows another way to solve the problem also
I attached the leg to the table, tighten all the screws on the other pedestal mounts (floor and table) and then used some electrical pipe mounting clamps to hold the folding leg firmly on the floor. I found the "bolt"/"screw" (forget what it is called) that has threads on one end and wood screw on other to screw into the floor and wing nuts to clamp the table into place.
Works great. Still have plenty of leg access and room.
__________________
Larry
2015 F350 Ultra Lariat CrewCab Long Bed 6.7L
2005 Keystone Outback Sydney 30FRKS
|
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|