|
03-18-2017, 05:50 PM
|
#1
|
Member
Join Date: Mar 2017
Location: Colorado Springs
Posts: 84
|
Proper jacking point
On a triple axle where is the proper point to jack when changing a tire. I think I read it should be done on the frame but wasn't too clear where. I've see others place the jack under the axle as close as they can get to the drum. Looking for the proper jack placement.
__________________
MACHINIST
[muh-shee-nist]
Someone who solves problems you didn't know you had in a way you don't understand.
See also: Wizard, Magician.
2012 Fuzion 405
|
|
|
03-18-2017, 07:39 PM
|
#2
|
Site Team
Join Date: Jul 2014
Location: Modesto
Posts: 20,350
|
Frame is the preferred place. Does your trailer have auto level? If so just use manual mode and lift that side off the ground.
__________________
2012 Copper Canyon 273FWRET being towed by a 1994 Ford F350 CC,LB,Dually diesel.
Airlift 5000 bags, Prodigy brake control, 5 gauges on the pillar.Used to tow a '97 Jayco 323RKS.
Now an RVIA registered tech. Retired from Law enforcement in 2008 after 25+ yrs.
|
|
|
03-18-2017, 10:08 PM
|
#3
|
Senior Member
Join Date: Apr 2012
Location: Portland, OR
Posts: 4,223
|
Well I have worked on my own vehicles for over 50 years. If I jack on the frame I need to raise the frame nearly a foot to get a flat tire off the ground. On top of that the jack needs to start about a foot to 18" off the ground to start with.
I place a bottle jack directly under the spring location on the axle tube, and only need to raise about six inches with the jack on ground!
__________________
Russ & Paula and Belle the Beagle.
2016 Ram Laramie 3500 DRW 14,000# GVWR (New TV)
2005 Copper Canyon 293 FWSLS 32’ GVWR 12,360
Visit and enjoy Oregon State Parks
|
|
|
03-19-2017, 03:00 AM
|
#4
|
Senior Member
Join Date: Oct 2014
Location: Germantown, TN
Posts: 6,333
|
Huhhh, you've brought up the only discussion on this board that beats which pickup brand is better! (Ford, of course)
Chuckster is voicing what is in the owner's manual from the axle manufacturer because some idiots down the road have jacked up the wheels in the middle of the axle, thereby bending said axle.
Rhagfo covered the method preferred by most members. Certainly a tried and true solution.
What is about to come up on the board will be a number of members using pieces of plastic sold on the 'net and at CW which when driven upon raise said wheel off the ground usually suitable for tire changing.
Take your pick. I jack on the area where the spring meets the axle.
__________________
Jim in Memphis, Wife of 51 years is Brenda
2019 F450 6.7 Powerstroke
2018 Mobile Suites 40RSSA
2021 40' Jayco Eagle
2001 Road king w/matching Harley sidecar
2021 Yamaha X2 Wolverine 1000
|
|
|
03-19-2017, 03:24 AM
|
#5
|
Senior Member
Join Date: Oct 2016
Location: "Murvil, TN
Posts: 2,212
|
Well, since you mentioned it notanlines, I do have the Anderson Rapid Jack, and I tried it out a couple of weeks ago in the driveway. It works perfectly in my application and lifted the "flat" tire about an inch off of the ground......about the perfect height for changing out a flat. From what I've read, depending on the spacing of the wheels on a tandem axle setup, center to center distance, it may not work for some trailers......but it did for mine. I'm happy, as it is much easier than crawling under the trailer to place a bottle jack. BTW, I also have a 12 Ton bottle jack that I will be carrying in the tool box of my truck, just in case something doesn't quite work out on the Rapid Jack system. To me, it's pretty cheap insurance to have a reliable backup method.
__________________
2016 F350 King Ranch Crew Cab Dually Diesel 4x4
2018 Grand Design Momentum 394M
2023 Suzuki GSX-S1000GT+
Excessive payload capacity is a wonderful thing
"If it ain't Fast....It ain't Fun"
|
|
|
03-19-2017, 04:16 AM
|
#6
|
Senior Member
Join Date: Apr 2013
Location: Haymarket, VA
Posts: 382
|
What I've found works when I've the time is to jack a few inches on the frame and then jack the axle at the U bolt off the ground. Changing a tire on the road may be different, and the only single place I'd jack would be on the U bolt.
__________________
'06 F350 Lariat turbo diesel dually, Curt 20k, Softopper, Aerosheld, coolant filter, air bags
'10 3665RE Hickory, wet bolts, Trimetric battery monitor, 4 100w panels & Morningstar TS-45, still tweeking!
|
|
|
03-19-2017, 08:42 AM
|
#7
|
Senior Member
Join Date: Jul 2014
Location: Nevada
Posts: 2,695
|
Jacking on the frame is the recommended method by the manufacturer, but on the shoulder of the road it might not be the most practical. If you jack on the spring ubolt close to the tire with a bottle jack you will only compress the spring and not lift the trailer. On a soft shoulder, at a possible angle, I think that makes more sense than jacking on the frame for a higher amount of lift to clear the tire off the ground. You have to decide what is best for you.
__________________
Desert185 🇺🇸 (Retired Chemtrail vendor)
-Ram 2500 QC, LB, 4x4, Cummins HO/exhaust brake, 6-speed stick.
-Andersen Ultimate 24K 5er Hitch.
-2014 Cougar 326SRX, Maxxis tires w/TPMS, wet bolts, two 6v batts.
-Four Wheel 8' Popup Camper.
|
|
|
03-19-2017, 11:54 AM
|
#8
|
Site Team
Join Date: Feb 2014
Location: W. Texas
Posts: 17,695
|
The less height the better, particularly on a slanted road side. I carry 2 bottle jacks, boards, etc. etc. I also carried one of those Trailer Aid Plus ramps you drive the good tire up on. Found it wasn't tall enough. Put a 2x on top of it (when placed under it it just slid) and the tire barely came off flat. Had to use my small shovel to dig out under the wheel to get the spare back on it so I'm not so sure about it. It IS a lot more stable than suspending things in the air on a bottle jack IMO.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|