|
05-27-2017, 05:22 PM
|
#1
|
Member
Join Date: Aug 2016
Location: Simi Valley CA
Posts: 43
|
Equalizing grey tanks?
I have a 2017 Carbon 357 with 2 grey tanks. I assume that 1 serves the garage bathroom & w/d drain and the other serves the front master bath and kitchen sink. Both tanks have seperate valves but drain to the same outlet. I installed a valve at the main outlet because I got tired of the surprise liquid that spurts out when I remove the cap. My question is, could I leave both grey valves open and let the tanks equalize therefore increasing the capacity of the most used front tank? I had a Prevost driver tell me that he does this on his rig. Is it safe on toyhaulers or not recommended? Thanks for any info.
|
|
|
05-27-2017, 05:31 PM
|
#2
|
Site Team
Join Date: Jul 2014
Location: Modesto
Posts: 20,350
|
I suppose it would work. Until MY 2018! Imagine by Grand design had 2 grays with one valve.
__________________
2012 Copper Canyon 273FWRET being towed by a 1994 Ford F350 CC,LB,Dually diesel.
Airlift 5000 bags, Prodigy brake control, 5 gauges on the pillar.Used to tow a '97 Jayco 323RKS.
Now an RVIA registered tech. Retired from Law enforcement in 2008 after 25+ yrs.
|
|
|
05-27-2017, 07:04 PM
|
#3
|
Site Team
Join Date: Mar 2011
Location: Gaylord
Posts: 26,997
|
Yes, it will work to equalize the two tanks. We do that when dry camping quite often. Since we use paper plates (they make good fire starters after eating) we don't have a lot of gray water dumped into the galley tank. So, we also have a terminal valve slide that we leave closed and I open both gray tank dump valves. That allows gray water from the bathroom tank to flow to the galley tank extending our stay (before the tanks are full) by a couple of days.
It sounds like Grand Designs plumbed the Imagine gray tanks "behind a single valve" so they will always equalize. Every time I have to crawl under the slide to pull the galley valve, I wonder why there's even a dump valve back there. It would have been so much easier to just have installed the front gray valve in the "T" rather than behind it. That would have eliminated the need for a valve under the slide.
__________________
John
2015 F250 6.7l 4x4
2014 Cougar X Lite 27RKS
|
|
|
05-27-2017, 07:09 PM
|
#4
|
Site Team
Join Date: Jul 2014
Location: Modesto
Posts: 20,350
|
And they added a second gray valve this year. Still one termination point.
__________________
2012 Copper Canyon 273FWRET being towed by a 1994 Ford F350 CC,LB,Dually diesel.
Airlift 5000 bags, Prodigy brake control, 5 gauges on the pillar.Used to tow a '97 Jayco 323RKS.
Now an RVIA registered tech. Retired from Law enforcement in 2008 after 25+ yrs.
|
|
|
05-28-2017, 06:20 AM
|
#5
|
Senior Member
Join Date: Feb 2014
Location: radium hot springs bc
Posts: 2,007
|
Quote:
Originally Posted by evanhix
I have a 2017 Carbon 357 with 2 grey tanks. I assume that 1 serves the garage bathroom & w/d drain and the other serves the front master bath and kitchen sink. Both tanks have seperate valves but drain to the same outlet. I installed a valve at the main outlet because I got tired of the surprise liquid that spurts out when I remove the cap. My question is, could I leave both grey valves open and let the tanks equalize therefore increasing the capacity of the most used front tank? I had a Prevost driver tell me that he does this on his rig. Is it safe on toyhaulers or not recommended? Thanks for any info.
|
I installed one of those quick connect valves at the black/grey tank outlet drain. Have always left both grey tanks open since doing this.
__________________
2018 Ram 3500 6.4 Harvest Edition
2018 Cougar 27RESWE
|
|
|
05-28-2017, 09:33 AM
|
#6
|
Member
Join Date: Aug 2016
Location: Simi Valley CA
Posts: 43
|
Any idea why they would design the tanks this way? Why not have one large tank that is shared be all grey water drains? Or plumb both together so that they can be shared?
|
|
|
05-28-2017, 09:52 AM
|
#7
|
Site Team
Join Date: Mar 2011
Location: Gaylord
Posts: 26,997
|
Quote:
Originally Posted by evanhix
Any idea why they would design the tanks this way? Why not have one large tank that is shared be all grey water drains? Or plumb both together so that they can be shared?
|
Probably "engineering specifications" like distributing the weight load, space limitations like where would you put a 80 gallon tank vs placement of two smaller tanks (in available spaces), cold weather applications like maintaining a "drain slope" inside the "conditioned spaces" of the floor while preventing exposed plumbing from becoming "frozen pipes".
If you think about it from a practical application, having two tanks in different locations in the floor, you can distribute the weight and not affect "balance". Having one large tank (in the front or in the back) would have a significant impact on tongue weight or pin weight. There's only so much space "over the axles", and not all the tanks can go there. On most trailers with two tanks, one is forward of the axles and one is behind them.
It's all about "carrying weight" without unbalancing the load.... I know, not an easy concept to master, and Keystone hasn't completely "mastered the concept" in all of their trailers, but in most, tongue weight remains a fairly constant percentage of total weight throughout the weight range from empty weight to maximum GVW. They do it by placement of available storage locations within the trailer and available tank storage for liquids.
__________________
John
2015 F250 6.7l 4x4
2014 Cougar X Lite 27RKS
|
|
|
06-04-2017, 09:19 PM
|
#8
|
Member
Join Date: May 2017
Location: Southern Oregon
Posts: 46
|
Quote:
Originally Posted by evanhix
I have a 2017 Carbon 357 with 2 grey tanks. I assume that 1 serves the garage bathroom & w/d drain and the other serves the front master bath and kitchen sink. Both tanks have seperate valves but drain to the same outlet. I installed a valve at the main outlet because I got tired of the surprise liquid that spurts out when I remove the cap. My question is, could I leave both grey valves open and let the tanks equalize therefore increasing the capacity of the most used front tank? I had a Prevost driver tell me that he does this on his rig. Is it safe on toyhaulers or not recommended? Thanks for any info.
|
How hard was it to add the valve also could you post a pic?
|
|
|
06-05-2017, 04:18 AM
|
#9
|
Site Team
Join Date: Mar 2011
Location: Gaylord
Posts: 26,997
|
sandfreak,
There is no actual "installation" involved. The valve that is being discussed is an aftermarket "twist-on" valve by Valterra (there are other companies that make similar valves). You simply remove your "end cap" (where you attach the dump hose), twist the valve onto the 4 barbs, then reinstall your "end cap" on the outer side of the new valve. It operates just like your existing valves, pull to open, push to close. That will allow your gray water to flow from the full tank to the "normal outlet" but instead of flowing into the dump hose, it flows "upstream" (via the drain line) and equalizes the volume between the two tanks.
Adding the valve to your terminal connector serves an even more "refreshing" advantage. It prevents the "gush of goo (or poo)" that can happen if you have a leaking dump valve on a tank. Once you ever experience the "surprise behind the cap" you'll know just why Valterra sells so many of these "little lifesavers"......
Here's a picture of the valve. It's available for about $20 at most RV parts stores, online at any RV parts outlet as well as Amazon, EBay and other sources.
__________________
John
2015 F250 6.7l 4x4
2014 Cougar X Lite 27RKS
|
|
|
06-05-2017, 06:47 AM
|
#10
|
Member
Join Date: May 2017
Location: Southern Oregon
Posts: 46
|
Quote:
Originally Posted by JRTJH
sandfreak,
There is no actual "installation" involved. The valve that is being discussed is an aftermarket "twist-on" valve by Valterra (there are other companies that make similar valves). You simply remove your "end cap" (where you attach the dump hose), twist the valve onto the 4 barbs, then reinstall your "end cap" on the outer side of the new valve. It operates just like your existing valves, pull to open, push to close. That will allow your gray water to flow from the full tank to the "normal outlet" but instead of flowing into the dump hose, it flows "upstream" (via the drain line) and equalizes the volume between the two tanks.
Adding the valve to your terminal connector serves an even more "refreshing" advantage. It prevents the "gush of goo (or poo)" that can happen if you have a leaking dump valve on a tank. Once you ever experience the "surprise behind the cap" you'll know just why Valterra sells so many of these "little lifesavers"......
Here's a picture of the valve. It's available for about $20 at most RV parts stores, online at any RV parts outlet as well as Amazon, EBay and other sources.
|
Thank you...
|
|
|
06-05-2017, 09:41 AM
|
#11
|
Member
Join Date: Aug 2016
Location: Simi Valley CA
Posts: 43
|
Quote:
Originally Posted by Sandfreak
How hard was it to add the valve also could you post a pic?
|
This is the permanent valve that I installed from amazon. I previously used the quick connect bayonet style but it hung down to low and I was afraid of clearance. Otherwise it worked well. Permanent install was simple. Hacksawed the old valve off and pvc glued the new valve on. Took about 10 minutes.
|
|
|
06-05-2017, 11:42 AM
|
#12
|
Gone Traveling
Join Date: May 2016
Location: Highland, IL
Posts: 512
|
I would love to do that, however my plumbing won't allow for it. I have three tanks: one black and two gray... with two discharges: one servicing the black and one gray, the other servicing the second gray.
No biggy though.
Sent from my iPhone using Tapatalk
|
|
|
08-02-2017, 03:59 PM
|
#13
|
Senior Member
Join Date: Jul 2017
Location: Davie
Posts: 331
|
Quote:
Originally Posted by evanhix
I have a 2017 Carbon 357 with 2 grey tanks. I assume that 1 serves the garage bathroom & w/d drain and the other serves the front master bath and kitchen sink. Both tanks have seperate valves but drain to the same outlet. I installed a valve at the main outlet because I got tired of the surprise liquid that spurts out when I remove the cap. My question is, could I leave both grey valves open and let the tanks equalize therefore increasing the capacity of the most used front tank? I had a Prevost driver tell me that he does this on his rig. Is it safe on toyhaulers or not recommended? Thanks for any info.
|
I wish they had a map of the system and a standard.
My rear black tank does rear toilet and washer. I know this because I seldom use rear toilet and have a washer I use alot. And it gets filled. Upon draining, the water is mostly clear with a slight tint of whatever color the detergent is. Lol
|
|
|
08-03-2017, 04:26 AM
|
#14
|
Senior Member
Join Date: Jan 2012
Location: Central San Joaguin Valley, CA
Posts: 2,117
|
Quote:
Originally Posted by evanhix
This is the permanent valve that I installed from amazon. I previously used the quick connect bayonet style but it hung down to low and I was afraid of clearance. Otherwise it worked well. Permanent install was simple. Hacksawed the old valve off and pvc glued the new valve on. Took about 10 minutes.
|
Hopefully you won't encounter any issues down the road - but - the sewer drain pipes are ABS plastic and I don't know if PVC glue will melt the ABS together correctly. Just sayin'
__________________
Jack & Marty
2018 Laredo 298 SRL
2011 F-250 SB Crew Cab 4x4 6.7L
|
|
|
08-03-2017, 04:42 AM
|
#15
|
Senior Member
Join Date: May 2015
Location: Near Saratoga Springs,
Posts: 1,131
|
Quote:
Originally Posted by jsmith948
Hopefully you won't encounter any issues down the road - but - the sewer drain pipes are ABS plastic and I don't know if PVC glue will melt the ABS together correctly. Just sayin'
|
The two types of plastics will bond with the right 'glue', called transition cement and is Oatey Transition Cement 30925. Anything else - probably wont last with any pressure
|
|
|
08-13-2017, 06:50 PM
|
#16
|
Member
Join Date: Aug 2016
Location: East Bay, CA
Posts: 30
|
Quote:
Originally Posted by Outback 325BH
I would love to do that, however my plumbing won't allow for it. I have three tanks: one black and two gray... with two discharges: one servicing the black and one gray, the other servicing the second gray.
No biggy though.
Sent from my iPhone using Tapatalk
|
I have the same configuration in our 324CG, and the galley grey tank is forward with the cleanout under the slide. I'm trying to figure out a way to delete it and move it near the aft cleanout area.
__________________
Proud Navy Dad
PowerShell by day - Tinkerer by night
'16 Keystone Outback 324CG/'04 F250 Bullettproof 6.0L
Blogg@ - https://rv-therapy.com/blog/
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|