|
03-30-2018, 03:11 PM
|
#1
|
Member
Join Date: Jan 2018
Location: Cincinnati
Posts: 55
|
water pump issue
I just de-winterized our camper, and had the following problem: I filled the water tank about half way. When I turned on the pump, it continued to run, until I shut it off. So, the pump is running, yet no water is coming through the faucets. And, the pump won't shut off unless you shut down the switch. The city water went through fine, and I cleared all of the lines of winterizer, checked for leaks, and all was good. Any ideas? Thanks
|
|
|
03-30-2018, 05:13 PM
|
#2
|
Site Team
Join Date: Mar 2011
Location: Gaylord
Posts: 26,997
|
It sounds like the pump "inlet" is not drawing water from the fresh water tank. Depending on how your trailer is plumbed, you may have a valve that is turned to draw antifreeze into the pump and that valve needs to be turned "back to the other position" to draw water from the FW tank. Or, you may have a separate fitting with a hose on it that you must install on the pump inlet to draw antifreeze and then reinstall the FW tank hose/fitting to draw from the tank. If that fitting is damaged or the O-ring is not sealing properly, air will be drawn into the pump and it can't create a vacuum to pull water from the tank.
So, check your valves if you have a "water system center" and check your fittings on the inlet side of the water pump if you have a "old fashioned" system.
__________________
John
2015 F250 6.7l 4x4
2014 Cougar X Lite 27RKS
|
|
|
03-30-2018, 05:44 PM
|
#3
|
Member
Join Date: Jan 2018
Location: Cincinnati
Posts: 55
|
Thanks for the advice, John....I do have a bypass valve with short hose to draw the antifreeze when winterizing. I put that little hose into a cup of water, withe the valve turned down - nothing happened. Then I did the same thing with the valve turned the other way - still nothing. Do you think maybe a screen should be checked?
|
|
|
03-30-2018, 05:53 PM
|
#4
|
Site Team
Join Date: Jul 2014
Location: Modesto
Posts: 20,353
|
Yes check the screen and the housing. I’ve seen the housing crack.
__________________
2012 Copper Canyon 273FWRET being towed by a 1994 Ford F350 CC,LB,Dually diesel.
Airlift 5000 bags, Prodigy brake control, 5 gauges on the pillar.Used to tow a '97 Jayco 323RKS.
Now an RVIA registered tech. Retired from Law enforcement in 2008 after 25+ yrs.
|
|
|
03-30-2018, 06:25 PM
|
#5
|
Site Team
Join Date: Mar 2011
Location: Gaylord
Posts: 26,997
|
I agree. If you have a "screen and filter housing" between the FW tank and the pump, they sometimes crack with freezing, and if there was any water in the pump head and it froze, it may have cracked the head. If either happened, the pump won't draw water or pump water into the system. Check the screen and housing, possibly pull the pump and remove the pump head. There are 4 screws to take it off the motor. Pay attention to how it comes apart so you can put it back together without spare parts!!!!
Possibly you can identify the damage/cracked housing. You can buypass the filter/screen if you choose, but risk getting sawdust or plastic shavings into your pump and can damage the diaphragm. So, if you do remove the screen and housing, I'd replace it ASAP. If the pump head is damaged, you can buy a pump head for about $30 and sometimes hard to find locally, but a new pump is usually readily available and costs about $50- $75. If you've been thinking about upgrading your pump, this would be a time to consider the plunge. Or, you can just buy a replacement like the one that is damaged and it will be a "direct one for one exchange".
__________________
John
2015 F250 6.7l 4x4
2014 Cougar X Lite 27RKS
|
|
|
03-31-2018, 04:00 AM
|
#6
|
Member
Join Date: Jan 2018
Location: Cincinnati
Posts: 55
|
I'm going to go over and check it out today, (when it gets warmer!). Thanks very much for all the tips, too!
|
|
|
03-30-2018, 06:32 PM
|
#7
|
Senior Member
Join Date: Dec 2017
Location: Lisbon
Posts: 551
|
Did you have a faucet open when you were running the pump? It can't prime if there's no flow path open.
Sent from my Nexus 6P using Tapatalk
__________________
2018 Keystone Cougar 22RBS
2020 Ford F-350 XLT SC SRW 6.7l Powerstroke.
|
|
|
03-31-2018, 04:12 AM
|
#8
|
Member
Join Date: Jan 2018
Location: Cincinnati
Posts: 55
|
I gave it plenty of time to get primed, but I am going to utilize you guys tips
|
|
|
03-31-2018, 05:36 AM
|
#9
|
Senior Member
Join Date: Feb 2017
Location: Dade City
Posts: 1,039
|
Do you have the Anderson Kantleak 4 way valve? If you do it may be the Issue. I've replaced mine twice. Simple to pull apart and check.
Remove the black knob
Remove the set screw, bottom of brass ring (its hidden)
Remove Brass Ring
Reinstall Black knob, twist and pull out
DO Not use petroleum products to reinstall.
Below is link to purchase repair kit
http://www.fitzilla.com/Store/page188.html
Hope this helps
|
|
|
03-31-2018, 05:42 AM
|
#10
|
Member
Join Date: Jan 2018
Location: Cincinnati
Posts: 55
|
Thank you, Frank G. Will check it out today!
|
|
|
03-31-2018, 05:59 AM
|
#11
|
Senior Member
Join Date: Dec 2017
Location: Lisbon
Posts: 551
|
Quote:
Originally Posted by rogeru
I gave it plenty of time to get primed, but I am going to utilize you guys tips
|
I know it was a silly question but you never know. Hope you get it going with out too much trouble. I'm sure it's nothing that a few days of hard work and a few thousand bucks $$ can't fix! [emoji6]
Sent from my Nexus 6P using Tapatalk
__________________
2018 Keystone Cougar 22RBS
2020 Ford F-350 XLT SC SRW 6.7l Powerstroke.
|
|
|
03-31-2018, 09:14 AM
|
#12
|
Member
Join Date: Jan 2018
Location: Cincinnati
Posts: 55
|
Just what we need.....someone who thinks he's a funny man. Gee, Steveo57....maybe you could be on Colbert's show.
|
|
|
03-31-2018, 09:28 AM
|
#13
|
Member
Join Date: Jan 2018
Location: Cincinnati
Posts: 55
|
Steveo57: I owe you an apology. I didn't see your first post, and only read your second one......thanks for trying to help me out. I'm sorry for the wise guy response.
|
|
|
03-31-2018, 06:51 AM
|
#14
|
Senior Member
Join Date: Feb 2013
Location: Lacey, WA
Posts: 503
|
Hi,
I have had the same problem before.
For some reason the pump would not prime. I opened the valve that controls the short hose that is used for winterizing and poured water down it to fill the cavity in the pump. Then closed the valve and turned on the pump... Wa-Laa is worked.
Lee
__________________
Lee & Christie
1970 F250 Highboy 4x4
2013 Cougar 21RBSWE
|
|
|
04-02-2018, 04:07 AM
|
#15
|
Junior Member
Join Date: Apr 2018
Location: Sterling
Posts: 1
|
Quote:
Originally Posted by rogeru
I just de-winterized our camper, and had the following problem: I filled the water tank about half way. When I turned on the pump, it continued to run, until I shut it off. So, the pump is running, yet no water is coming through the faucets. And, the pump won't shut off unless you shut down the switch. The city water went through fine, and I cleared all of the lines of winterizer, checked for leaks, and all was good. Any ideas? Thanks
|
Either the pump impeller is not working to pump the water or the pumped water is just going in circles inside the heater with nowhere to go due to valves still close or it has not pressurized the system yet. First, i would check for air coming out pf faucets. When the system pressurize first we get air and water follows. On that case just wait. If no air something is wrong. Double check valves while pump runs, if air starts to rush thru faucets go to number one. If that fails it could be the impeller. Pull the pump out and verify the impeller works and pumps water out. It sounds to me is not pressurizing. I would start by checking the pump first. Disconnect the pipe closest to the pump and look to see if it is pumping air. Good luck!
Sent from my iPhone using Tapatalk
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|