|
05-27-2020, 08:33 AM
|
#1
|
Junior Member
Join Date: May 2020
Location: white lake
Posts: 4
|
Slideout topper passport 34mb
Has anyone successfully installed a slide-out topper on a 2018 passport 34mb? I bought 3 slide-out awnings from lippert and on the rear slidout on left side there is a vent on the top and bottom of the slide where the fridge is. however with this vent on top it is only an 1" from the top of the slidout frame. my question is how do you attach the bracket that is supposed to go into the top corner of the slidout to hold the awning?? any help much appreciated.
|
|
|
06-13-2020, 04:07 AM
|
#2
|
Junior Member
Join Date: May 2020
Location: white lake
Posts: 4
|
Quote:
Originally Posted by iroc454
Has anyone successfully installed a slide-out topper on a 2018 passport 34mb? I bought 3 slide-out awnings from lippert and on the rear slidout on left side there is a vent on the top and bottom of the slide where the fridge is. however with this vent on top it is only an 1" from the top of the slidout frame. my question is how do you attach the bracket that is supposed to go into the top corner of the slidout to hold the awning?? any help much appreciated.
|
No ideas? Anyone
|
|
|
06-13-2020, 05:10 AM
|
#3
|
Site Team
Join Date: Jul 2014
Location: Modesto
Posts: 20,237
|
Just saw this. We have moved the brackets to the bottom edge of the flange. You’ll have to move the awning rail if you don’t have the proper slope.
__________________
2012 Copper Canyon 273FWRET being towed by a 1994 Ford F350 CC,LB,Dually diesel.
Airlift 5000 bags, Prodigy brake control, 5 gauges on the pillar.Used to tow a '97 Jayco 323RKS.
Now an RVIA registered tech. Retired from Law enforcement in 2008 after 25+ yrs.
|
|
|
06-15-2020, 05:24 AM
|
#4
|
Junior Member
Join Date: May 2020
Location: white lake
Posts: 4
|
Quote:
Originally Posted by chuckster57
Just saw this. We have moved the brackets to the bottom edge of the flange. You’ll have to move the awning rail if you don’t have the proper slope.
|
If I'm understanding you correctly, instead of mounting the backets just below the flange, I should mount to the actual flange? It just seems like the bracket would just pul out of the flange or bend it? Would u have a pic where ur brackets are? Thanks for ur input
|
|
|
06-15-2020, 06:39 AM
|
#5
|
Site Team
Join Date: Mar 2011
Location: Gaylord
Posts: 26,846
|
I think what Chuck is referring to is mounting the bracket "on the flange" but through the aluminum framework of the slideout, to which the flange is mounted) so in essence, you're mounting it to the slideout frame, through the flange... He's not (IMHO) referring to actually bolting the bracket to the thin plastic flange above the slide body...
An alternative is to position the bracket over the upper refrigerator vent, mark it where the bracket sits over it, then remove the vent, CAREFULLY cut away the part that the bracket sits on top of the vent, reinstall the vent and then install the bracket. You may have to "glue the vent door into the frame along that edge, but since the upper vent door is seldom removed, it wouldn't matter that it's "semi-permanently secured in place. This option would provide the most "like the original intent" for mounting.
__________________
John
2015 F250 6.7l 4x4
2014 Cougar X Lite 27RKS
|
|
|
06-15-2020, 07:42 AM
|
#6
|
Site Team
Join Date: Feb 2014
Location: W. Texas
Posts: 17,601
|
I think I would go trimming the vent cover. I went out and looked at mine and the brackets are about 2" in height. If you have 1" available under the lip of the flange you would need an additional inch off the vent cover. Just cut out to fit around the bracket and seal. I would think that would come out being where it is supposed to be and like it was meant to be there.
__________________
Danny and Susan, wife of 56 years
2019 Ram 3500 Laramie CC SWB SB 6.4 4x4 4.10
2020 Montana High Country 331RL
|
|
|
06-15-2020, 08:57 AM
|
#7
|
Site Team
Join Date: Jul 2014
Location: Modesto
Posts: 20,237
|
I have mounted the brackets on the bottom edge of the top flange, that uses the frame of the slide. I don’t have pics because that was customer units a year or so ago.
__________________
2012 Copper Canyon 273FWRET being towed by a 1994 Ford F350 CC,LB,Dually diesel.
Airlift 5000 bags, Prodigy brake control, 5 gauges on the pillar.Used to tow a '97 Jayco 323RKS.
Now an RVIA registered tech. Retired from Law enforcement in 2008 after 25+ yrs.
|
|
|
08-10-2020, 01:38 AM
|
#8
|
Junior Member
Join Date: May 2020
Location: white lake
Posts: 4
|
Quote:
Originally Posted by chuckster57
I have mounted the brackets on the bottom edge of the top flange, that uses the frame of the slide. I don’t have pics because that was customer units a year or so ago.
|
Thanks Chuck. That's what I did and everything is good .
|
|
|
|
Thread Tools |
|
Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|