|
02-19-2014, 10:40 AM
|
#1
|
Junior Member
Join Date: Apr 2012
Location: Michigan
Posts: 27
|
RV Stabilizer Positioning
I own a 30 foot travel trailer with quad bunks in the back and the master bedroom in the front. I snug up each of the scissor jacks and I use two Bal X-Chocks between each set of tires. However, there is still quite a bit of movement within the trailer.
I am interested in getting a set of RV stabilizers (either Bal Lock-Arm or Steadyfast). I was considering installing one stabilizer on each scissor jack going from side to side. This should stop most side to side motion. I figure that the X-Chocks are stopping most of the the fore/aft movement so there shouldn't be a need to mount any of the stabilzers front to back.
What are your thoughts/opinions on this?
|
|
|
02-19-2014, 12:20 PM
|
#2
|
Senior Member
Join Date: Sep 2011
Location: Wisconsin
Posts: 105
|
Steadyfast
Quote:
Originally Posted by far733
I own a 30 foot travel trailer with quad bunks in the back and the master bedroom in the front. I snug up each of the scissor jacks and I use two Bal X-Chocks between each set of tires. However, there is still quite a bit of movement within the trailer.
I am interested in getting a set of RV stabilizers (either Bal Lock-Arm or Steadyfast). I was considering installing one stabilizer on each scissor jack going from side to side. This should stop most side to side motion. I figure that the X-Chocks are stopping most of the the fore/aft movement so there shouldn't be a need to mount any of the stabilzers front to back.
What are your thoughts/opinions on this?
|
Love my Steadyfast. Takes out 90-95% of the movement. Great customer service as well.
|
|
|
02-19-2014, 12:30 PM
|
#3
|
Junior Member
Join Date: Apr 2012
Location: Michigan
Posts: 27
|
Thanks for the response! I have not decided which set I am going to go with yet.
I'm trying to figure out the best way to install the stabilizers to minimize the movement (i.e. one pair in the front for side to side and then another pair on the back for side to side; one pair for side to side and the other pair for front to rear; one pair for side to side and the other pair for front to rear with both placed in either the front or back; or one pair installed on one corner for both side to side and front to rear and then another set on the opposite corner, same relation). Even with my scissor jacks fully extended and with two X-chocks, my TT has a considerable amount of movement.
|
|
|
02-19-2014, 12:37 PM
|
#4
|
Senior Member
Join Date: Apr 2013
Location: Oklahoma
Posts: 1,077
|
We have 2 sets of Bal. One bar mounted front to back on each jack. Cut down the wiggle tremendously.
__________________
Kristi & Jeff
2014 Cougar 313 rli
2013 F350 king ranch
2014 passport 2650bh (sold)
2009 GMC 2500HD 6.6L 4X4 (sold)
|
|
|
02-19-2014, 12:54 PM
|
#5
|
Junior Member
Join Date: Apr 2012
Location: Michigan
Posts: 27
|
Quote:
Originally Posted by Kristi
We have 2 sets of Bal. One bar mounted front to back on each jack. Cut down the wiggle tremendously.
|
Do you use any between the wheel chocks with your set up (or did you prior to the install of your Bals)?
|
|
|
02-19-2014, 01:07 PM
|
#6
|
Senior Member
Join Date: May 2010
Location: Rochester, NY
Posts: 1,605
|
Side to side will probably be all you need if your wheels are positively chocked. I would start with side to side lock arms on front and rear stabilizers and see how that works.
Keep in mind that with a longer trailer, you will almost always experience frame flex and suspension bounce from movement in the trailer. If I am staying at a site for more than a couple of days, I sometimes place bottle jacks under the frame at the leaf spring equalizer, which reduces the flexing and suspension movement.
|
|
|
02-19-2014, 07:28 PM
|
#7
|
Senior Member
Join Date: Feb 2013
Location: MA
Posts: 3,153
|
We use the Valterra stabilizers. We know we will always have movement but we also go out of level when we open the slides so we are trying to limit that as well.
__________________
2013 Premier 31BHPR
2014 F350 6.2L
Soon to be just DW and I
|
|
|
02-20-2014, 09:28 AM
|
#8
|
Junior Member
Join Date: Apr 2012
Location: Michigan
Posts: 27
|
Quote:
Originally Posted by therink
Side to side will probably be all you need if your wheels are positively chocked. I would start with side to side lock arms on front and rear stabilizers and see how that works.
Keep in mind that with a longer trailer, you will almost always experience frame flex and suspension bounce from movement in the trailer. If I am staying at a site for more than a couple of days, I sometimes place bottle jacks under the frame at the leaf spring equalizer, which reduces the flexing and suspension movement.
|
They are positively chocked (I used X-Chocks btwn both sets of wheels and I re-tighten them after the tires cool).
I'm still torn on the best way to install them. I'm pretty sure that I will purchase two sets (4 stabilizers). I have considered installing all 4 going side to side. However, I'm wondering how it would work if I installed them on opposite corners with one pair installed on one rear corner for both side to side and front to rear and then another set on the front opposite corner, same relation. It seems that this way would support the triangulation theories.
Thoughts?
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
All times are GMT -8. The time now is 04:30 PM.