|
07-30-2015, 02:38 PM
|
#1
|
Junior Member
Join Date: Apr 2014
Location: Utah
Posts: 6
|
LCI level up-external sensor error
Had some troubles with the LCI 6 point level up last trip out. Hopefully these pics work. Tight wires, a sharp corner, and 2500 miles.
I fixed it and it works now. I am hoping this will help anyone who finds themselves with this same problem.
|
|
|
08-30-2021, 05:40 AM
|
#2
|
Junior Member
Join Date: Apr 2021
Location: Smyrna
Posts: 4
|
I experienced the same error on my 2017 Avalanche 330GR after a 2800 mile trip. All threads I read on this error indicated the remote leveling sensor located in the rear center of the camper just behind the spare tire in the under belly. I did inspect the wires and plug but saw nothing obvious. I ordered and replaced the sensor (Amazon $160). Still same error, continuity checked the harness front to back but had some quirky readings. I called Lippert tech support and was told it was more than likely the control module located in the ceiling of the front storage compartment. Ordered and replaced it (Lippert $404.95 plus $7.94 shipping) but still the same error. I removed the wiring from the conduit on the harness side at the rear sensor and sure enough one of the wires was chaffed and corroded. So just some advise, remove the wiring from the conduit at the leveling sensor in the back a good 3-4 feet behind the plug and inspect closely. Mine was pinched or chaffed about two feet behind the plug. To repair the underbelly I used a 1x 6 and 3/4 inch #8 wood screws to mend the cuts that were made by the previous owner or RV repair facility. As you can see in the pictures they used old window trim 3/4 inch thick with 3 inch dry wall screws, hence the chaffed wire. I’m so glad there wasn’t a holding tank any where near this really poor attempt to hold up a cut underbelly. The part numbers; remote sensor 14022, control module (brain) 307272. Lippert Support (574) 537-8900. There is a 20% restocking fee to return a part to Lippert.
|
|
|
10-15-2021, 02:29 PM
|
#3
|
Junior Member
Join Date: Dec 2018
Location: Phoenix
Posts: 13
|
Sensor location?
We were setting up in our camp spot today and got an error on the Lippert ground control 3.0 "external sensor error"
From my research so far it is either the leveling sensor in back , behind the axles or wiring to that sensor.
Problem is I can't find the sensor. The manual says it is 2 or 3 feet behind the rear axle mounted to a crossmember. Of course with all the plastic bottom I can't see anything and don't want to just start cutting holes. Anyone have a better idea where this sensor is located?
2021 Keystone Cougar 24RDS
Thanks!
|
|
|
10-15-2021, 02:46 PM
|
#4
|
Site Team
Join Date: Jul 2014
Location: Modesto
Posts: 20,353
|
Quote:
Originally Posted by TNordine
We were setting up in our camp spot today and got an error on the Lippert ground control 3.0 "external sensor error"
From my research so far it is either the leveling sensor in back , behind the axles or wiring to that sensor.
Problem is I can't find the sensor. The manual says it is 2 or 3 feet behind the rear axle mounted to a crossmember. Of course with all the plastic bottom I can't see anything and don't want to just start cutting holes. Anyone have a better idea where this sensor is located?
2021 Keystone Cougar 24RDS
Thanks!
|
If you can remove the screws along the edge, or if it has nails just pop them off/out and replace with SS self tapping screws.
__________________
2012 Copper Canyon 273FWRET being towed by a 1994 Ford F350 CC,LB,Dually diesel.
Airlift 5000 bags, Prodigy brake control, 5 gauges on the pillar.Used to tow a '97 Jayco 323RKS.
Now an RVIA registered tech. Retired from Law enforcement in 2008 after 25+ yrs.
|
|
|
10-15-2021, 07:21 PM
|
#5
|
Senior Member
Join Date: Jul 2013
Location: Box Elder
Posts: 2,910
|
Photos at the first post sure look like rodent damage. If the wires are repaired, the system may work again.
__________________
Bob & Becky
2012 3402 Montana
2012 Chevy 2500HD D/A CC
|
|
|
10-16-2021, 08:22 AM
|
#6
|
Site Team
Join Date: Mar 2011
Location: Gaylord
Posts: 26,997
|
Quote:
Originally Posted by bobbecky
Photos at the first post sure look like rodent damage. If the wires are repaired, the system may work again.
|
Very likely.... Today's "low price bid" wiring is insulated with a "new fangled plastic" made from soy oil (rather than from petroleum oil).. To mice, rats and voles, it smells "just like food" and actually is a "form of rat trap bait" if you consider how it smells.... If it'll attract rats to a old fashioned rat trap, it'll attract them to chew through the plastic wire loom to get to "lunch".....
__________________
John
2015 F250 6.7l 4x4
2014 Cougar X Lite 27RKS
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
All times are GMT -8. The time now is 05:58 AM.