|
|
04-20-2021, 02:41 PM
|
#1
|
Junior Member
Join Date: Apr 2020
Location: Council
Posts: 21
|
Secure recliners on slideout
Have 20 hideout 26hlswe want to replace sofa with recliners. How do I secure the recliners . The sofa is screwed to sides . Can I screw the recliners to slide floor without doing damage? What have others done to secure recliners.
|
|
|
04-20-2021, 03:08 PM
|
#2
|
Senior Member
Join Date: Aug 2020
Location: Upper Chesapeake Bay
Posts: 4,838
|
Quote:
Originally Posted by edwardsm1
Have 20 hideout 26hlswe want to replace sofa with recliners. How do I secure the recliners . The sofa is screwed to sides . Can I screw the recliners to slide floor without doing damage? What have others done to secure recliners.
|
Wonder if it would be better to drill up through the slide floor and bolt them or screw them from below so you don’t have any screws protruding down that may interfere with slide operation
Or just use a strap around the base and screw to where the sofa attached
__________________
2020 Cougar 315 RLS
2020 Ram 3500 6.7HO 4.10 Dually Aisin
|
|
|
04-20-2021, 06:24 PM
|
#3
|
Senior Member
Join Date: Dec 2017
Location: Wandering the Country
Posts: 596
|
Hmmm. Correct me if I'm wrong, but the outside bottom of the slide is covered with darco. And it's (outside) entire flat surface rubs on the wear bar when the slide goes in and out. If all that's correct I would not want any penetration through the darco, and I would not want any fastener (metal or otherwise) to rub the wear bar every time the slide goes in and out.
I don't know how thick the slide floor is, I'm guessing 1/2inch OSB. so that's not very thick to sink a wood screw into down from the inside. And you can't let a screw tip go through and stick out the bottom.
If it was me I'd find an RV with recliners installed and crawl under the raised foot end and see how the factory did it, what they used.
Just my thoughts
|
|
|
04-20-2021, 06:41 PM
|
#4
|
Senior Member
Join Date: Aug 2012
Location: Waco, Tx
Posts: 5,457
|
Just a note: the two recliners in my slide are not bolted to anything. And haven't moved an inch in 3500 miles.
Just saying
__________________
2015 Ford F350 DRW 6.7 Diesel XL
2020 Avalanche 313 RS
|
|
|
04-20-2021, 06:45 PM
|
#5
|
Senior Member
Join Date: Aug 2020
Location: Upper Chesapeake Bay
Posts: 4,838
|
Quote:
Originally Posted by mikec557
Hmmm. Correct me if I'm wrong, but the outside bottom of the slide is covered with darco. And it's (outside) entire flat surface rubs on the wear bar when the slide goes in and out. If all that's correct I would not want any penetration through the darco, and I would not want any fastener (metal or otherwise) to rub the wear bar every time the slide goes in and out.
I don't know how thick the slide floor is, I'm guessing 1/2inch OSB. so that's not very thick to sink a wood screw into down from the inside. And you can't let a screw tip go through and stick out the bottom.
If it was me I'd find an RV with recliners installed and crawl under the raised foot end and see how the factory did it, what they used.
Just my thoughts
|
Quote:
Originally Posted by Javi
Just a note: the two recliners in my slide are not bolted to anything. And haven't moved an inch in 3500 miles.
Just saying ��
|
Yeah forget what I said I don’t have enough experience with slideout construction
__________________
2020 Cougar 315 RLS
2020 Ram 3500 6.7HO 4.10 Dually Aisin
|
|
|
04-20-2021, 06:53 PM
|
#6
|
Senior Member
Join Date: Nov 2017
Location: Picacho, Az
Posts: 6,809
|
Quote:
Originally Posted by Javi
Just a note: the two recliners in my slide are not bolted to anything. And haven't moved an inch in 3500 miles.
Just saying ��
|
Had recliners in my last 3 5th wheels none of which were bolted down.
If you feel it necessary to do something before travel, turn them back to back tightly in the corner.
__________________
Full-timed 10+ years
Sold '13 Redwood FB
Traded '13 GMC Denali DRW D/A
Replacement undetermined
|
|
|
04-20-2021, 07:35 PM
|
#7
|
Junior Member
Join Date: Apr 2020
Location: Council
Posts: 21
|
Yea don't want to start poking holes. I think we'll just sit the chairs in and figure a way to secure them when we travel if need be. I want thank you all for info and thoughts.
|
|
|
04-20-2021, 07:43 PM
|
#8
|
Senior Member
Join Date: Dec 2017
Location: Wandering the Country
Posts: 596
|
After I posted I went off and trolled through YouTube. And I think I've seen everything that could be done. One had used carriage bolts through the darco and floor, using washers and nuts inside to hold the furniture down. Several have, as already mentioned, just set them in place. One laid another piece of 1/2in wood on the floor inside and then placed the furniture on that. After watching it all, I would join the camp of set them in place and fugitaboutem.
But my curiosity wants to know, how is the original furniture secured to the floor, if it is at all.
|
|
|
04-20-2021, 08:08 PM
|
#9
|
Senior Member
Join Date: Jul 2013
Location: Box Elder
Posts: 2,910
|
Our rig came with swivel recliners at the rear, and we've since replaced them with different swivel recliners, and with over 70,000 miles on this rig, they've never moved nor have they been anchored in place. They are on carpet which helps keep them in place, smooth flooring might be a different story.
__________________
Bob & Becky
2012 3402 Montana
2012 Chevy 2500HD D/A CC
|
|
|
04-20-2021, 09:05 PM
|
#10
|
Senior Member
Join Date: Apr 2012
Location: Portland, OR
Posts: 4,223
|
Quote:
Originally Posted by Javi
Just a note: the two recliners in my slide are not bolted to anything. And haven't moved an inch in 3500 miles.
Just saying ��
|
Well I agree with Javi! Our recliners were not bolted down, and we never strapped down. Couch in slide out was not attached to anything free to move. We also didn’t strap down our charges at the dining room table.
__________________
Russ & Paula and Belle the Beagle.
2016 Ram Laramie 3500 DRW 14,000# GVWR (New TV)
2005 Copper Canyon 293 FWSLS 32’ GVWR 12,360
Visit and enjoy Oregon State Parks
|
|
|
04-21-2021, 02:47 AM
|
#11
|
Senior Member
Join Date: Mar 2015
Location: Southeastern Connectiut
Posts: 1,306
|
Plus 1 for Russ ^^^.
Dining room Chairs and recliners have traveled "loose" for 8 years now with no issues. I have even put my bar stools on the couch, and found them right where I left them. I have however, needed to secure cabinet doors, and obviously take stuff off of counters.
Good Luck,
__________________
Pull Toy
Steve & Jan, Ava & Emma (Mini Schnauzers):
2016 F350 Lariat 4X4 Powerstroke CC/SB "PULLTOY V"
2013 Alpine 3535RE "MAGIC CARPET IV"
Proud Navy Vet!
|
|
|
04-21-2021, 02:53 AM
|
#12
|
Senior Member
Join Date: Aug 2012
Location: Waco, Tx
Posts: 5,457
|
Quote:
Originally Posted by Javi
Just a note: the two recliners in my slide are not bolted to anything. And haven't moved an inch in 3500 miles.
Just saying ��
|
As an addendum... The two recliners in my previous Cougar were not secured either and survived 6 years and 10,791 miles without moving.
__________________
2015 Ford F350 DRW 6.7 Diesel XL
2020 Avalanche 313 RS
|
|
|
04-21-2021, 04:57 AM
|
#13
|
Senior Member
Join Date: Sep 2020
Location: Jacksonville
Posts: 993
|
This is what I like about everyone here. Can always find good info. I’m getting ready to change out the seating in mine and replace with two new regular recliners and was thinking about the same thing. Now I know just put them in.
__________________
Bob/Kay
Jacksonville, Nc
2020 Keystone Cougar 5th wheel 29 rks traded now
2021 3761 fl Montana 5th wheel
Pulled with a 2022 F350 King Ranch
Retired LEO after 35 years just enjoying life now.
|
|
|
04-21-2021, 05:41 AM
|
#14
|
Senior Member
Join Date: Mar 2014
Location: Mountain Home, Idaho
Posts: 3,015
|
The less holes you put in things the better off you will be.. In eight years with this fifth wheel the two recliners have never been an issue.. they are not secured to anything and I travel on forest roads and same rough roads here in the west. wife places a small throw rug between the two recliners so they dont chaff against each other and the metal table she has between them
__________________
2007 GMC Classic club cab 4x4 Duramax LBZ
2014 Alpine 3010 RE. 34 foot fifth wheel
|
|
|
04-21-2021, 07:21 AM
|
#15
|
Site Team
Join Date: Feb 2014
Location: W. Texas
Posts: 17,695
|
We have theater seating (2 recliners side by side with a console) in this trailer. They are screwed to the floor of the slide with screws approx. 1" long as I recall. That said, in previous trailers the recliners were not attached and for that matter we didn't even strap down the kitchen table chairs; nary a problem in thousands of miles on our great highways and byways. I wouldn't worry about attaching them until it proved to be a problem, which I doubt.
__________________
Danny and Susan, wife of 56 years
2019 Ram 3500 Laramie CC SWB SB 6.4 4x4 4.10
2020 Montana High Country 331RL
|
|
|
04-21-2021, 09:14 AM
|
#16
|
Site Team
Join Date: Mar 2011
Location: Gaylord
Posts: 26,997
|
The rocker recliners in our Springdale had to be moved from "camping position" to "travel position" to get the slide closed. There was no way to "screw them in place" without having to "unscrew them to travel'....
The rocker recliners in our Cougar are "sat in place to travel" and "moved out a bit to recline while camped"...
There are two "rings screwed to the top of the carpeted floor" that are intended to be used to "strap the recliners in place during travel".
We used the straps the first couple of trips, then DW suggested, "Why don't we see if them move without being tied down"... I completely agreed (saved me more time and effort) and they didn't move. Since then (almost 7 years of travel) they haven't moved from where we put them and honestly, I don't have a clue where the straps might have gone or if they might even had "dry rotted" by now.... If I find them, I'll let you know
Here's a strap like what is in our Cougar. They're available on Amazon at https://www.amazon.com/RecPro-Furnit...19324612&psc=1 for about $10 each. But, if I could find ours, you'd be welcome to them if they are still even in one piece.
__________________
John
2015 F250 6.7l 4x4
2014 Cougar X Lite 27RKS
|
|
|
04-21-2021, 12:32 PM
|
#17
|
Senior Member
Join Date: Jul 2015
Location: Windsor
Posts: 236
|
Quote:
Originally Posted by JRTJH
The rocker recliners in our Springdale had to be moved from "camping position" to "travel position" to get the slide closed. There was no way to "screw them in place" without having to "unscrew them to travel'....
The rocker recliners in our Cougar are "sat in place to travel" and "moved out a bit to recline while camped"...
There are two "rings screwed to the top of the carpeted floor" that are intended to be used to "strap the recliners in place during travel".
We used the straps the first couple of trips, then DW suggested, "Why don't we see if them move without being tied down"... I completely agreed (saved me more time and effort) and they didn't move. Since then (almost 7 years of travel) they haven't moved from where we put them and honestly, I don't have a clue where the straps might have gone or if they might even had "dry rotted" by now.... If I find them, I'll let you know
Here's a strap like what is in our Cougar. They're available on Amazon at https://www.amazon.com/RecPro-Furnit...19324612&psc=1 for about $10 each. But, if I could find ours, you'd be welcome to them if they are still even in one piece.
|
Mine are like John describes. Have not anchored that strap in ever. starting our 6th season.
__________________
2016 Cougar 1/2 Ton Series 283 RETWE
2018 F150 EcoBoost FX4 Lariat Max-Tow and Heavy Duty Payload Package
|
|
|
04-29-2021, 09:52 AM
|
#18
|
Senior Member
Join Date: Sep 2019
Location: Jacksonville
Posts: 538
|
Screw to floor if you don’t intend to move them around.
The slide out flooring is 5/8 to 3/4. You don’t need huge lag bolts! Probably just four 3/4” - 1” screws depending on chair frame you go through.
__________________
2020 Cougar Half Ton 29RKS Fifth Wheel
2019 F350 4WD Lariat SRW 6.7 Diesel SD
Anderson Ultimate 5th Hitch - JT Strongarm TST509 TPMS- 2200W(8)Solar Panels - 800AH BattleBorn Batteries. 3000W Victron MultiPlus II Inv. SoftStartRV on 2 AC’s - Predator 3500 generator Airlift 5000 bags
|
|
|
04-29-2021, 10:38 AM
|
#19
|
Senior Member
Join Date: May 2013
Location: Reedsport
Posts: 322
|
We put a love seat in our slide on the Cougar. Doesn't move at all. We did have a Bullet with chairs at the rear. They did move around but came with straps which helped.
__________________
2007 Keystone Cougar 243RKS
2019 Ford F150 S/Crew ECOBoost
|
|
|
04-29-2021, 12:33 PM
|
#20
|
Senior Member
Join Date: Feb 2019
Location: Wickenburg
Posts: 3,314
|
Quote:
Originally Posted by Camping family
This is what I like about everyone here. Can always find good info. I’m getting ready to change out the seating in mine and replace with two new regular recliners and was thinking about the same thing. Now I know just put them in.
|
In our last year with our old TT, DW prevailed upon me to remove the jackknife couch (which both of us hated) and install two domestic La-Z-Boys she found for a song, that fit the cavity. We couldn't bolt them down because they were non-zero-clearance mechanisms, so we had to scoot them out to recline. I did install strap anchors (non-Darco slide) for travel, and (as always) got criticized for "always having to nuclear harden everything." DW was correct, the recliners didn't visibly budge over four weeks of road travel.
__________________
2019 Cougar 26RBSWE
2019 Ford F-250
|
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|