|
|
02-09-2020, 04:38 PM
|
#1
|
Member
Join Date: Aug 2019
Location: Austin
Posts: 58
|
Dometic furnace woes
I have a new 2019 Carbon 417 Toy hauler. The furnace problem started virtually the first week that we were full timing. Here's what it does.
Blower comes on for about 10 seconds and then you can hear the furnace ignite and puts out heat exactly like it's supposed to. This last for 4-5 days, then no heat.
After that, blower comes on and runs for 45 seconds or so and then shuts off.
I called a local service man and he has been out 4 times...only charged me 1 service call fee. He replaced the limit switch last time....was going to replace the sail switch, but apparently everyone is out of stock.
Funny.....everytime he comes out and disconnects the furnace to work on it, it works for a few days....then kaput.
It is a Dometic model DFMD 35121
I have the troubleshooting guide, and have researched all of the repair techniques here and on youtube...question is where to go next, should I pull it out and check all connections??.......replace the sail switch when one is available??? order a new circuit board off amazon??
Thoughts....Suggestions??
One other thing....I have already replaced the 12cf Nevercold fridge....it worked for one week...replaced it with a residential model. Norcold sent a brand new replacement a few weeks later that I am selling.
Wiring.......gas lines etc do not scare me, but I am tired of paying for repairs that last only a few days.
We are full timers, so there is no chance we will be dropping the unit off at a shop......although I may pull out the heater and take it in for repairs under warranty.
We are currently near Austin TX.
Tim
|
|
|
02-09-2020, 05:02 PM
|
#2
|
Site Team
Join Date: Feb 2014
Location: W. Texas
Posts: 17,695
|
Others will chime in with different ideas but I'm thinking control board. If it works for days just fine, drops off the charts and starts cycling the fan, you disconnect it and it works fine again for a few days - that sounds like a control board to me. Had a very similar issue and to get through a cold spell I went out and disconnected the power lead, let it reset?, reconnected it and I was good to go for a bit. New control board fixed it.
__________________
Danny and Susan, wife of 56 years
2019 Ram 3500 Laramie CC SWB SB 6.4 4x4 4.10
2020 Montana High Country 331RL
|
|
|
02-09-2020, 05:06 PM
|
#3
|
Site Team
Join Date: Jul 2014
Location: Modesto
Posts: 20,351
|
I’m leaning towards a board too. If you get a repair under warranty, Dometic will require OEM board. If you pay, buy a dinosaur brand.
__________________
2012 Copper Canyon 273FWRET being towed by a 1994 Ford F350 CC,LB,Dually diesel.
Airlift 5000 bags, Prodigy brake control, 5 gauges on the pillar.Used to tow a '97 Jayco 323RKS.
Now an RVIA registered tech. Retired from Law enforcement in 2008 after 25+ yrs.
|
|
|
02-09-2020, 05:26 PM
|
#4
|
Senior Member
Join Date: Feb 2019
Location: Wickenburg
Posts: 3,314
|
In my new rig, my sail switch was fouled by sawdust and leftover styro chips. Is it possible yours is also fouled, and the impacts involved in servicing the heater knock off just enough fouling to make it operate until the crud blows back onto it?
If you have spare time, maybe you could try a no-cost cure of removing the sail switch, cleaning it, and taking a vacuum to the cavity. Might work.
__________________
2019 Cougar 26RBSWE
2019 Ford F-250
|
|
|
02-09-2020, 10:11 PM
|
#5
|
Member
Join Date: Jan 2020
Location: Carson City
Posts: 35
|
Dang! I have the same model with the same problem and have a repairman coming Wednesday. Hope they have the parts.
|
|
|
02-10-2020, 06:34 PM
|
#6
|
Member
Join Date: Aug 2019
Location: Austin
Posts: 58
|
Thanks for all the comments gang.
The parts are out of stock everywhere online, and my repair guy is still waiting on one from Dometic....they are also out of stock.
From all the comments I think I'll go ahead and order the dinosaur board, and pull the heater out.....check the operation of the sail switch....check all connections etc. Last time it worked for 4 days before crapping out....frustrating!!!!
It will be a few days before I have time to do the repair, as I am working on my new RV pole barn here in Texas....will post back my results when finished with repairs.
Tim
|
|
|
02-10-2020, 07:02 PM
|
#7
|
Member
Join Date: Aug 2019
Location: Austin
Posts: 58
|
Which Dinosaur board for the Dometic DFMD 35121 furnace....anyone know??
Tim
|
|
|
02-10-2020, 07:17 PM
|
#8
|
Site Team
Join Date: Mar 2011
Location: Gaylord
Posts: 26,997
|
Quote:
Originally Posted by toolittletime
Which Dinosaur board for the Dometic DFMD 35121 furnace....anyone know??
Tim
|
Give Dinosaur Electronics a call at (541) 994-4344. They are open 8-5 Monday through Friday Pacific time. Have your furnace model and serial number handy and they will tell you exactly what you need to order.
__________________
John
2015 F250 6.7l 4x4
2014 Cougar X Lite 27RKS
|
|
|
02-11-2020, 07:08 AM
|
#9
|
Member
Join Date: Aug 2019
Location: Austin
Posts: 58
|
Thank you John!!
|
|
|
02-11-2020, 08:53 AM
|
#10
|
Senior Member
Join Date: Dec 2018
Location: grand rapids
Posts: 596
|
how about talking to dometic...they may help.
if it is a 2019 I would assume it is under warranty...push for warranty coverage reimbursement from keystone.
|
|
|
03-03-2020, 04:37 AM
|
#11
|
Member
Join Date: Aug 2019
Location: Austin
Posts: 58
|
Thanks all....
I called Dinosaur as suggested and they recommended the Fan 50 plus board available on Amazon for 91.00. I pulled the heater and installed the board and it has been working perfectly (fingers crossed) for the past week. The board was a little bit of a pain since the corner mounting lugs had to be removed carefully without breaking the corner off the board. While I had it out I tested the sail switch.....it was working properly.
The biggest pita was having to crawl in the belly and disconnect everything, and then pull the heater through a hole I had cut in the bottom of the pantry. Other option was to remove and reinstall the water heater......not!!! Sucks having to cut a hole in a new trailer, but I put everything back in with screws, so the next time I have to access it,and I'm sure I will, I will not be cussing as much.
Tim
|
|
|
03-21-2020, 02:18 PM
|
#12
|
Senior Member
Join Date: May 2013
Location: Aliso Viejo Ca
Posts: 108
|
I’ve been battling the same issue. Control board and thermostat were replaced in Late Feb. Two days ago it stopped igniting again. On tank was empty so I got it filled and reset everything. Last night it stopped igniting again. All my efforts to reset failed. These include turn the breaker off and removing power from control board. The light on the ignition board was on then off for three seconds. Manual states a Limit / Airflow error. Last troubleshooting step was to remove and inspect sail switch. I saw nothing on the switch and no debris blocking airflow. After re-install of sail switch all has been functioning. I have ordered two just in case. Would you RV experts recommend I replace the limit switch as well?
The is a Atwood-Dometic AFMD 35131. Installed on 2018 Keystone Cougar 367FLS 5th wheel
__________________
|
|
|
03-21-2020, 02:36 PM
|
#13
|
Senior Member
Join Date: Feb 2019
Location: Wickenburg
Posts: 3,314
|
For what it's worth, I'm on my third Dometic furnace failure in a 2019 rig, and I determined that the furnace comes with a two-year warranty, the second year of which is covered by Dometic. Your dealer may or may not be an approved Dometic warranty center; luckily, mine is. As of last Wednesday, my rig is back in again to get the furnace repaired under warranty.
I know a lot of you people are skilled enough to do these jobs yourself and get them done right, but on the other hand, maybe if Dometic has to eat enough warranty labor, especially in the second year when they don't have Keystone to cover it, they will learn how to make a reliable heating system.
__________________
2019 Cougar 26RBSWE
2019 Ford F-250
|
|
|
03-21-2020, 02:46 PM
|
#14
|
Senior Member
Join Date: May 2013
Location: Aliso Viejo Ca
Posts: 108
|
Thanks, as soon as I can it is headed for a service shop. I do have an extended warranty
__________________
|
|
|
03-21-2020, 03:26 PM
|
#15
|
Site Team
Join Date: Jul 2014
Location: Modesto
Posts: 20,351
|
Quote:
Originally Posted by LHaven
For what it's worth, I'm on my third Dometic furnace failure in a 2019 rig, and I determined that the furnace comes with a two-year warranty, the second year of which is covered by Dometic. Your dealer may or may not be an approved Dometic warranty center; luckily, mine is. As of last Wednesday, my rig is back in again to get the furnace repaired under warranty.
I know a lot of you people are skilled enough to do these jobs yourself and get them done right, but on the other hand, maybe if Dometic has to eat enough warranty labor, especially in the second year when they don't have Keystone to cover it, they will learn how to make a reliable heating system.
|
Dometic pays the warranty labor, during the first year Keystone is the warranty “administrator”, and acts as the middleman. After the first year the dealer will deal directly with Dometic. In the end Keystone doesn’t pay, the appliance manufacturer does.
__________________
2012 Copper Canyon 273FWRET being towed by a 1994 Ford F350 CC,LB,Dually diesel.
Airlift 5000 bags, Prodigy brake control, 5 gauges on the pillar.Used to tow a '97 Jayco 323RKS.
Now an RVIA registered tech. Retired from Law enforcement in 2008 after 25+ yrs.
|
|
|
03-21-2020, 04:33 PM
|
#16
|
Senior Member
Join Date: May 2013
Location: Aliso Viejo Ca
Posts: 108
|
Quote:
Originally Posted by jlonginav
I’ve been battling the same issue. Control board and thermostat were replaced in Late Feb. Two days ago it stopped igniting again. On tank was empty so I got it filled and reset everything. Last night it stopped igniting again. All my efforts to reset failed. These include turn the breaker off and removing power from control board. The light on the ignition board was on then off for three seconds. Manual states a Limit / Airflow error. Last troubleshooting step was to remove and inspect sail switch. I saw nothing on the switch and no debris blocking airflow. After re-install of sail switch all has been functioning. I have ordered two just in case. Would you RV experts recommend I replace the limit switch as well?
The is a Atwood-Dometic AFMD 35131. Installed on 2018 Keystone Cougar 367FLS 5th wheel
|
Just a update. About 4 hrs running good. Now we have some decent rating and thunderstorms. I’m now getting the ignition lockout error. Fires up 3 times but won’t stay on.
__________________
|
|
|
03-21-2020, 04:46 PM
|
#17
|
Member
Join Date: Aug 2019
Location: Austin
Posts: 58
|
Quote:
Originally Posted by jlonginav
I’ve been battling the same issue. Control board and thermostat were replaced in Late Feb. Two days ago it stopped igniting again. On tank was empty so I got it filled and reset everything. Last night it stopped igniting again. All my efforts to reset failed. These include turn the breaker off and removing power from control board. The light on the ignition board was on then off for three seconds. Manual states a Limit / Airflow error. Last troubleshooting step was to remove and inspect sail switch. I saw nothing on the switch and no debris blocking airflow. After re-install of sail switch all has been functioning. I have ordered two just in case. Would you RV experts recommend I replace the limit switch as well?
The is a Atwood-Dometic AFMD 35131. Installed on 2018 Keystone Cougar 367FLS 5th wheel
|
Did you replace the control board with the same as original, or the Dinosaur brand?
|
|
|
03-21-2020, 05:05 PM
|
#18
|
Senior Member
Join Date: May 2013
Location: Aliso Viejo Ca
Posts: 108
|
It was replaced at a service center so I suspect an original
__________________
|
|
|
03-21-2020, 05:13 PM
|
#19
|
Site Team
Join Date: Jul 2014
Location: Modesto
Posts: 20,351
|
If Dometic paid a warranty claim, OEM is required.
__________________
2012 Copper Canyon 273FWRET being towed by a 1994 Ford F350 CC,LB,Dually diesel.
Airlift 5000 bags, Prodigy brake control, 5 gauges on the pillar.Used to tow a '97 Jayco 323RKS.
Now an RVIA registered tech. Retired from Law enforcement in 2008 after 25+ yrs.
|
|
|
03-21-2020, 05:29 PM
|
#20
|
Member
Join Date: Aug 2019
Location: Austin
Posts: 58
|
That could be the problem......just sayin !
|
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|