Journey with Confidence RV GPS App RV Trip Planner RV LIFE Campground Reviews RV Maintenance Take a Speed Test Free 7 Day Trial ×
 

Go Back   Keystone RV Forums > Keystone Fleet | Keystone RV Models > Fifth Wheels
Click Here to Login

Reply
 
Thread Tools Display Modes
 
Old 05-11-2022, 05:16 PM   #1
Z71
Junior Member
 
Join Date: Jan 2022
Location: Placitas
Posts: 16
Red face 24RDS adding a Progressive 50amp monitor

I would like to add an inline Progressive 50amp power monitor/surge protector unit. I know this will need to be mounted close to the power control center under the oven.


Don't know how much space is available under there, perhaps I can delete the lowest drawer directly to the right of the power/breaker center but that won't go over well with the wife.

I looked at the units that plug into the power pedestal then you plug into them but after looking into them carefully I found out they do not interrupt power like the internal progressive units do. I already lost my Dometic refrigerator control board at the Rincon Country West RV park in Tuscon AZ. We encountered a power surge that fried the refers control board plus popped the main circuit breaker in both my RV an a friends parked next door.

Apparently they had a vendor in the park working on the transformer that probably caused the problem they promptly denied. Needless to say they told me to pound sand, $180.00 bucks later we were back online.
So with that said, I had the progressive inline unit in my old RV and it always served me well cutting the power when things were bad. I will see if there is a way to install the unit in the Cougar. Anyone who has any insight on this please chime in.
__________________
Learn from yesterday, Live for today, Hope for tomorrow.
Albert Einstein
Z71 is offline   Reply With Quote
Old 05-11-2022, 05:57 PM   #2
sourdough
Site Team
 
Join Date: Feb 2014
Location: W. Texas
Posts: 14,462
What are you comparing? EMS (not surge protectors) from Southwire (Surge Guard), Progressive and the Hughes Watchdog all interrupt power when a problem is detected and shut the power down when plugged into a pedestal.
__________________
Danny & Susan wife of 54 years
2019 Ram 3500 Laramie CC SB 6.4 4x4 4.10
2020 Montana High Country 331RL
sourdough is offline   Reply With Quote
Old 05-12-2022, 07:43 AM   #3
wrvond
Senior Member
 
wrvond's Avatar
 
Join Date: Sep 2020
Location: Leon, WV
Posts: 225
I’m on my phone right now so will post pictures later, but wanted to let you know I installed mine under the booth seat where the power enters the camper.
__________________
2022 Cougar Half Ton 24RDS
2017 F350 DRW 6.7L


wrvond is offline   Reply With Quote
Old 05-12-2022, 08:29 AM   #4
travelin texans
Senior Member
 
travelin texans's Avatar
 
Join Date: Nov 2017
Location: Picacho Peak Rv Resort
Posts: 5,822
Quote:
Originally Posted by Z71 View Post
I would like to add an inline Progressive 50amp power monitor/surge protector unit. I know this will need to be mounted close to the power control center under the oven.


Don't know how much space is available under there, perhaps I can delete the lowest drawer directly to the right of the power/breaker center but that won't go over well with the wife.

I looked at the units that plug into the power pedestal then you plug into them but after looking into them carefully I found out they do not interrupt power like the internal progressive units do. I already lost my Dometic refrigerator control board at the Rincon Country West RV park in Tuscon AZ. We encountered a power surge that fried the refers control board plus popped the main circuit breaker in both my RV an a friends parked next door.

Apparently they had a vendor in the park working on the transformer that probably caused the problem they promptly denied. Needless to say they told me to pound sand, $180.00 bucks later we were back online.
So with that said, I had the progressive inline unit in my old RV and it always served me well cutting the power when things were bad. I will see if there is a way to install the unit in the Cougar. Anyone who has any insight on this please chime in.
Used a 50 amp PI EMS portable hanging from every pedestal we plugged into across this country with 3 different 5th wheels. Yes it would interrupt the power if necessary, same as the hardwired & saved us at least once that I know of for sure. I chose the portable as I knew we'd trade rvs so only had to buy it once, it never sprouted legs to walk away, I left it connected to the shore cord so it never got left behind. It would've been handy to have the remote display, but wasn't worth tossing out the one I had for the newer model.
__________________
Danny & Linda
Full-timed 10+ years
Sold '13 Redwood FB
Traded '13 GMC Denali DRW D/A
Currently rv & truckless
Replacement undetermined
travelin texans is offline   Reply With Quote
Old 05-12-2022, 10:27 AM   #5
wrvond
Senior Member
 
wrvond's Avatar
 
Join Date: Sep 2020
Location: Leon, WV
Posts: 225
Quote:
Originally Posted by Z71 View Post
I would like to add an inline Progressive 50amp power monitor/surge protector unit. I know this will need to be mounted close to the power control center under the oven.


Don't know how much space is available under there, perhaps I can delete the lowest drawer directly to the right of the power/breaker center but that won't go over well with the wife.

I looked at the units that plug into the power pedestal then you plug into them but after looking into them carefully I found out they do not interrupt power like the internal progressive units do. I already lost my Dometic refrigerator control board at the Rincon Country West RV park in Tuscon AZ. We encountered a power surge that fried the refers control board plus popped the main circuit breaker in both my RV an a friends parked next door.

Apparently they had a vendor in the park working on the transformer that probably caused the problem they promptly denied. Needless to say they told me to pound sand, $180.00 bucks later we were back online.
So with that said, I had the progressive inline unit in my old RV and it always served me well cutting the power when things were bad. I will see if there is a way to install the unit in the Cougar. Anyone who has any insight on this please chime in.
So, to install the unit under the dinette bench is the easiest thing in the world - as long as you are into anaconda wrestling!. There's no need for any material other than what comes with the EMS.
Make sure you have the shore cable unplugged and use a hacksaw to cut the wire under the bench seat. Cut the insulation back and install in the ECM per instructions. Tip: the instructions will tell you to orient the magnets with the arrows pointing a certain direction but there are no arrows. Don't worry about it, the new units don't care which direction the magnets point.
I then mounted the remote unit to the end of the bench so I can easily see it from pretty much everywhere in the camper.

Edit: BTW, if you are determined to mount it behind the power distribution center, there is plenty of room between the converter and the water heater. You may want to buy a 3 or 4 foot length of wire - I forget the designation- in order to reach. Also, IIRC, it won't help to remove the oven. I'm pretty sure when I looked up there it was an enclosed space. In other words, I couldn't see the bottom of the oven. Removing the power distribution panel won't buy you a lot of space to work in either. The best way in is to remove the divider wall under the sink and wriggle in on your left side. It's not comfortable.
Attached Thumbnails
Click image for larger version

Name:	Screenshot 2022-05-12 142009.jpg
Views:	10
Size:	176.6 KB
ID:	39711   Click image for larger version

Name:	Screenshot 2022-05-12 142132.jpg
Views:	7
Size:	112.1 KB
ID:	39712  
__________________
2022 Cougar Half Ton 24RDS
2017 F350 DRW 6.7L


wrvond is offline   Reply With Quote
Old 05-12-2022, 03:34 PM   #6
Z71
Junior Member
 
Join Date: Jan 2022
Location: Placitas
Posts: 16
Thats a much better solution to those units that just plug into the pedestal, I could not find one that fully cuts the power in case of low voltage and spikes, most just contain MOV's to try to contain the spike and are usually shot once they encounter one. The Progressive Industries 50amp inline unit like you installed offers it all and has a great warranty to boot.

Plus I wont have to figure out a way to keep someone from walking away with the plug in unit or how to plug it in when the park has the socket installed in upside down.

Nice job of thinking outside the box WRVOND and thanks for sharing that. I never thought of unscrewing the panel and looking in to see what was there.
__________________
Learn from yesterday, Live for today, Hope for tomorrow.
Albert Einstein
Z71 is offline   Reply With Quote
Old 05-12-2022, 03:40 PM   #7
sourdough
Site Team
 
Join Date: Feb 2014
Location: W. Texas
Posts: 14,462
Quote:
Originally Posted by Z71 View Post
Thats a much better solution to those units that just plug into the pedestal, I could not find one that fully cuts the power in case of low voltage and spikes, most just contain MOV's to try to contain the spike and are usually shot once they encounter one. The Progressive Industries 50amp inline unit like you installed offers it all and has a great warranty to boot.

Plus I wont have to figure out a way to keep someone from walking away with the plug in unit or how to plug it in when the park has the socket installed in upside down.

Nice job of thinking outside the box WRVOND and thanks for sharing that. I never thought of unscrewing the panel and looking in to see what was there.

If you hit a snag trying to put your EMS inside I will just say that I've always used a portable and never had a soul, anywhere, look like they wanted to take it. I've also been in campsites with the plug upside down but that can be remedied easily (remove the cover and plug the cable in upside down or turn the receptacle to the correct orientation). Good luck on getting a new EMS; South Wire (Surge Guard), Progressive Industries and Hughes make some good units that shut down incoming power problems.
__________________
Danny & Susan wife of 54 years
2019 Ram 3500 Laramie CC SB 6.4 4x4 4.10
2020 Montana High Country 331RL
sourdough is offline   Reply With Quote
Old 05-12-2022, 05:12 PM   #8
CedarCreekWoody
Senior Member
 
Join Date: Dec 2019
Location: Trinidad,TX
Posts: 690
The EMS can be mounted anywhere along the incoming power cable, such as under a bench. It doesn't have to be near power center.
__________________
Woody
Cedar Creek Lake, Texas
2019 Laredo 290 SRL
2019 Ram 2500, 4x4, Cummins diesel
Andersen hitch
CedarCreekWoody is offline   Reply With Quote
Old 05-12-2022, 09:40 PM   #9
travelin texans
Senior Member
 
travelin texans's Avatar
 
Join Date: Nov 2017
Location: Picacho Peak Rv Resort
Posts: 5,822
Quote:
Originally Posted by Z71 View Post
Thats a much better solution to those units that just plug into the pedestal, I could not find one that fully cuts the power in case of low voltage and spikes, most just contain MOV's to try to contain the spike and are usually shot once they encounter one. The Progressive Industries 50amp inline unit like you installed offers it all and has a great warranty to boot.

Plus I wont have to figure out a way to keep someone from walking away with the plug in unit or how to plug it in when the park has the socket installed in upside down.

Nice job of thinking outside the box WRVOND and thanks for sharing that. I never thought of unscrewing the panel and looking in to see what was there.
As I stated a few post back the portable Progressive Industries 50 amp "EMS" I used for several years functioned exactly the same as the hardwired model.
What you're describing sounds like just a surge protector not an EMS, not comparing apples to apples, a surge protector only is a waste of money.
__________________
Danny & Linda
Full-timed 10+ years
Sold '13 Redwood FB
Traded '13 GMC Denali DRW D/A
Currently rv & truckless
Replacement undetermined
travelin texans is offline   Reply With Quote
Old 05-13-2022, 05:31 AM   #10
markcee
Senior Member
 
markcee's Avatar
 
Join Date: Dec 2019
Location: Sun City West
Posts: 655
Quote:
Originally Posted by Z71 View Post
I would like to add an inline Progressive 50amp power monitor/surge protector unit. I know this will need to be mounted close to the power control center under the oven.


Don't know how much space is available under there, perhaps I can delete the lowest drawer directly to the right of the power/breaker center but that won't go over well with the wife.

I looked at the units that plug into the power pedestal then you plug into them but after looking into them carefully I found out they do not interrupt power like the internal progressive units do. I already lost my Dometic refrigerator control board at the Rincon Country West RV park in Tuscon AZ. We encountered a power surge that fried the refers control board plus popped the main circuit breaker in both my RV an a friends parked next door.
Quote:
Originally Posted by travelin texans View Post
As I stated a few post back the portable Progressive Industries 50 amp "EMS" I used for several years functioned exactly the same as the hardwired model.
What you're describing sounds like just a surge protector not an EMS, not comparing apples to apples, a surge protector only is a waste of money.
This thread kind of evolved into the merits of having an internal EMS for their inability to 'walk away' from a campsite.

I'm more interested in the comment in the original post about a pedestal mount EMS not having the same protection level as an internal hardwired version. I'm with Travelin Texans on this one....it's my understanding that a Progressive EMS PT50X for example will offer the exact same protection as the hardwired version.

No?
__________________
2020 Keystone Cougar '1/2 ton' TT, 29RLKWE
2019 F150 EB, Max Tow - TRADED
2019 F350, SRW, 6.2L, 4.30 gears
markcee is offline   Reply With Quote
Old 05-13-2022, 06:01 AM   #11
wrvond
Senior Member
 
wrvond's Avatar
 
Join Date: Sep 2020
Location: Leon, WV
Posts: 225
Quote:
Originally Posted by markcee View Post
This thread kind of evolved into the merits of having an internal EMS for their inability to 'walk away' from a campsite.

I'm more interested in the comment in the original post about a pedestal mount EMS not having the same protection level as an internal hardwired version. I'm with Travelin Texans on this one....it's my understanding that a Progressive EMS PT50X for example will offer the exact same protection as the hardwired version.

No?

The EMS-PT50X and the EMS-HW50C are functionally identical. Their only differences are related to the operating environment. In other words, the EMS-PT50X is weather proof and has a lock (among other things) that the EMS-HW50C does not. The EMS-HW50C has a remote display while the display on the PT50X is built in to the unit. One big difference is the hard wired unit is field serviceable, while the portable unit is not.
I personally prefer the hard wired unit for two reasons:
1. I got distracted and left a portable unit hanging on the power pedestal at a campground in North Carolina several years ago.
2. The hard wired unit's remote display is inside the camper. That's usually the first thing I look at when I am wondering how much power I'm drawing.

I suspect the confusion is being caused by the OP looking at the portable surge protectors such as the SSP-50X and comparing that to the EMS-HW50C.
Comparing the features of all the Progressive Industries products is rather difficult without printing their product information page.
__________________
2022 Cougar Half Ton 24RDS
2017 F350 DRW 6.7L


wrvond is offline   Reply With Quote
Old 05-13-2022, 06:11 AM   #12
RollaMo
Member
 
Join Date: Mar 2022
Location: Rolla
Posts: 51
Quote:
Originally Posted by wrvond View Post
I suspect the confusion is being caused by the OP looking at the portable surge protectors such as the SSP-50X and comparing that to the EMS-HW50C.
Comparing the features of all the Progressive Industries products is rather difficult without printing their product information page.

I agree.

Had I known how easy it was to get that Hard Wired unit in your 5th wheel, I probably would have went that route too.
But I went ahead and purchased the petal mount EMS-PT50X one before picking up the trailer so I would be ready.
__________________
2022 Cougar 24RDS
2019 GMC 2500HD (gas)
RollaMo is offline   Reply With Quote
Old 05-13-2022, 11:49 AM   #13
dutchmensport
Senior Member
 
Join Date: Jan 2013
Location: Indiana
Posts: 1,365
I have the portable Progressive EMS PT50X and it's been plugged in at home (50 amp RV power) and when camping, since the first moment we purchased the camper. The EMS has shut down the trailer on several occasions. On each and every time it shut down the camper it was due to the shore power breaker failing and campground maintenance had to replace with a new breaker at the post.
__________________
2019 Montana High Country 375FL
2014 Chevy Duramax HD 6.6 - 3500 Diesel Dully Long bed Crew Cab
dutchmensport is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Powered by vBadvanced CMPS v3.2.3
Disclaimer:

This website is not affiliated with or endorsed by the Keystone RV Company or any of its affiliates in any way. Keystone RVģ is a registered trademark of the Keystone RV Company.


All times are GMT -8. The time now is 03:00 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2022, vBulletin Solutions, Inc.