|
|
04-23-2021, 05:33 AM
|
#1
|
Member
Join Date: Mar 2016
Location: Swansea Illinois
Posts: 91
|
Lessons Learned on AC Install?
Good morning All,
I'm going to be installing a second AC on my travel trailer this weekend, and I wanted to reach out to the experts on here to see if you have any specific things I need to watch for?
I have a 2016 Laredo 314RE, it is prewired for the second AC in the bedroom, does have 50 am service that I use often, and the AC unit I bought was the Dometic Brisk Air II, 15k unit.
I did a search on this forum and found a bunch of post about AC units, but none specific enough to provide any detailed "gotcha's" to watch out for.
Any advice provided would be much appreciated.
Thanks
Dale
__________________
US Air Force Retired
2016 F250 Super Duty - Modified
(Air Bags, Extra Springs, Boxed in Frame, RV Cam, 4.10 Gears) Not your average F250
2022 Cougar 27 SGS
|
|
|
04-23-2021, 05:53 AM
|
#2
|
Site Team
Join Date: Jul 2014
Location: Modesto
Posts: 20,350
|
Does your unit have in command? Did you buy a ducted or non ducted AC? Thermostat controlled or plenum controlled?
__________________
2012 Copper Canyon 273FWRET being towed by a 1994 Ford F350 CC,LB,Dually diesel.
Airlift 5000 bags, Prodigy brake control, 5 gauges on the pillar.Used to tow a '97 Jayco 323RKS.
Now an RVIA registered tech. Retired from Law enforcement in 2008 after 25+ yrs.
|
|
|
04-23-2021, 05:58 AM
|
#3
|
Senior Member
Join Date: Dec 2019
Location: Sun City West
Posts: 907
|
Quote:
Originally Posted by dwdlt
Good morning All,
I'm going to be installing a second AC on my travel trailer this weekend, and I wanted to reach out to the experts on here to see if you have any specific things I need to watch for?
I have a 2016 Laredo 314RE, it is prewired for the second AC in the bedroom, does have 50 am service that I use often, and the AC unit I bought was the Dometic Brisk Air II, 15k unit.
I did a search on this forum and found a bunch of post about AC units, but none specific enough to provide any detailed "gotcha's" to watch out for.
Any advice provided would be much appreciated.
Thanks
Dale
|
Be careful getting it on the roof!
After mulling over various 'plans' I ended up putting the boxed unit in the bed of the truck and parked the truck alongside the trailer. I then stood a ladder up in the truck bed to the trailer at a pretty good angle and pushed the unit ahead of me to the roof to a waiting helper.
Using the truck bed cut several feet off the trip up and I could also use the bed rail as an intermediate point to set the box while I got into position.
Other than that, our install was pretty painless. About 2-1/2 hours start to finish including getting it talking to our InCommand system.
__________________
2022 Rockwood Signature 8324SB
2019 F350, SRW, 6.2L, 4.30 gears
Sold: 2020 Keystone Cougar '1/2 ton' TT, 29RLKWE
|
|
|
04-23-2021, 06:20 AM
|
#4
|
Member
Join Date: Mar 2016
Location: Swansea Illinois
Posts: 91
|
Quote:
Originally Posted by chuckster57
Does your unit have in command? Did you buy a ducted or non ducted AC? Thermostat controlled or plenum controlled?
|
It's non-ducted and plenum controlled. No in-command
__________________
US Air Force Retired
2016 F250 Super Duty - Modified
(Air Bags, Extra Springs, Boxed in Frame, RV Cam, 4.10 Gears) Not your average F250
2022 Cougar 27 SGS
|
|
|
04-23-2021, 06:22 AM
|
#5
|
Member
Join Date: Mar 2016
Location: Swansea Illinois
Posts: 91
|
Quote:
Originally Posted by markcee
Be careful getting it on the roof!
After mulling over various 'plans' I ended up putting the boxed unit in the bed of the truck and parked the truck alongside the trailer. I then stood a ladder up in the truck bed to the trailer at a pretty good angle and pushed the unit ahead of me to the roof to a waiting helper.
Using the truck bed cut several feet off the trip up and I could also use the bed rail as an intermediate point to set the box while I got into position.
Other than that, our install was pretty painless. About 2-1/2 hours start to finish including getting it talking to our InCommand system.
|
I'm seeing that will be a challenge. Thanks for the note
__________________
US Air Force Retired
2016 F250 Super Duty - Modified
(Air Bags, Extra Springs, Boxed in Frame, RV Cam, 4.10 Gears) Not your average F250
2022 Cougar 27 SGS
|
|
|
04-23-2021, 06:28 AM
|
#6
|
Site Team
Join Date: Oct 2011
Location: Joppa, MD
Posts: 11,757
|
First and foremast plan out your moves have what you need ready and COMMUNICATE clearly with your helper what your plans and moves are. Don't assume that they will "know where you are going" or" which way you will turn" when you get up there. I would place some protection on the roof before lugging an a/c unit over it. Some plywood (corners rounded anmd a moving blanket under it) so if you have to set it down you don't cut/puncture the roof membrane. Try to prepare or the "oh crap" moment ahead of time.
Good luck.
__________________
Marshall
2012 Laredo 303 TG
2010 F250 LT Super Cab, long bed, 4X4, 6.4 Turbo Diesel
|
|
|
04-23-2021, 06:48 AM
|
#7
|
Member
Join Date: Mar 2016
Location: Swansea Illinois
Posts: 91
|
Quote:
Originally Posted by flybouy
First and foremast plan out your moves have what you need ready and COMMUNICATE clearly with your helper what your plans and moves are. Don't assume that they will "know where you are going" or" which way you will turn" when you get up there. I would place some protection on the roof before lugging an a/c unit over it. Some plywood (corners rounded anmd a moving blanket under it) so if you have to set it down you don't cut/puncture the roof membrane. Try to prepare or the "oh crap" moment ahead of time.
Good luck.
|
Yep, thanks. That is sound advice. I have precut some cardboard to laydown on the roof. Going to put a blanket under it as well. I think damaging the roof is my biggest fear. I have a hoist setup in my pole barn as well, so I'm studying that and looking at lifting the AC up using the hoist first, and then backing the trailer underneath of it....Yea, "what could go wrong there" LOL. As crazy as that sounds, I believe it'll work. I'll try to take a pic or two and post it here
__________________
US Air Force Retired
2016 F250 Super Duty - Modified
(Air Bags, Extra Springs, Boxed in Frame, RV Cam, 4.10 Gears) Not your average F250
2022 Cougar 27 SGS
|
|
|
04-23-2021, 07:07 AM
|
#8
|
Member
Join Date: Jun 2018
Location: Overbrook
Posts: 52
|
The biggest problem I had was taking the vent off, it took up the most time. Lifted the AC up with bucket on tractor, and my DW helped with install, it took about 2 hrs total. Key is to take all the time you need!!
__________________
Kojac - Retired Army
2017 Ford F250 4x4 6.7 Diesel
2016 28.5 BHS Keystone Laredo
20K Reese Goosebox
|
|
|
04-23-2021, 07:13 AM
|
#9
|
Site Team
Join Date: Oct 2011
Location: Joppa, MD
Posts: 11,757
|
Quote:
Originally Posted by dwdlt
Yep, thanks. That is sound advice. I have precut some cardboard to laydown on the roof. Going to put a blanket under it as well. I think damaging the roof is my biggest fear. I have a hoist setup in my pole barn as well, so I'm studying that and looking at lifting the AC up using the hoist first, and then backing the trailer underneath of it....Yea, "what could go wrong there" LOL. As crazy as that sounds, I believe it'll work. I'll try to take a pic or two and post it here
|
If I had a pole barn and knew the rafter would support the unit on a hoist that's exactly what I would do.
__________________
Marshall
2012 Laredo 303 TG
2010 F250 LT Super Cab, long bed, 4X4, 6.4 Turbo Diesel
|
|
|
04-23-2021, 08:10 AM
|
#10
|
Site Team
Join Date: Jul 2014
Location: Modesto
Posts: 20,350
|
When you get the vent off, try to remove as much Dicor and putty/butyl tape as possible, That way the gasket will fit on a flat surface. When you tighten the 4 screws that hold the AC in place you want to compress the gasket to about 1/2 its original thickness and tighten the bolts in stages.
__________________
2012 Copper Canyon 273FWRET being towed by a 1994 Ford F350 CC,LB,Dually diesel.
Airlift 5000 bags, Prodigy brake control, 5 gauges on the pillar.Used to tow a '97 Jayco 323RKS.
Now an RVIA registered tech. Retired from Law enforcement in 2008 after 25+ yrs.
|
|
|
04-23-2021, 11:45 AM
|
#11
|
Senior Member
Join Date: Feb 2015
Location: Texas
Posts: 1,090
|
My son and I replaced the existing 15K AC on our trailer.
We used a ladder to slide the new unit up and the old unit down.
I also laid some 3/8" 2' X 4' plywood down, with towels under them to support my weight while on the roof.
It was a fairly easy job, with just the 2 of us.
-Brian
__________________
2014 Bullet Premier 22RBPR - let the camping commence!
2013 F150 Platinum - 5.0 - 3.55 ELD + towing package
|
|
|
04-23-2021, 12:10 PM
|
#12
|
Site Team
Join Date: Mar 2011
Location: Gaylord
Posts: 26,997
|
Using plywood or OSB is IMHO better than using a side from a cardboard box to lay the air conditioner on. There are some "sharp things" around the 14" opening and a cardboard box may not provide all the protection needed. A sheet of plywood or OSB with a towel/moving blanket under it is much harder for that sharp corner to cut through... If it happens to cut through, there's nothing between the "sharp and your TPO roof".....
__________________
John
2015 F250 6.7l 4x4
2014 Cougar X Lite 27RKS
|
|
|
04-26-2021, 02:39 AM
|
#13
|
Member
Join Date: Mar 2016
Location: Swansea Illinois
Posts: 91
|
Quote:
Originally Posted by chuckster57
When you get the vent off, try to remove as much Dicor and putty/butyl tape as possible, That way the gasket will fit on a flat surface. When you tighten the 4 screws that hold the AC in place you want to compress the gasket to about 1/2 its original thickness and tighten the bolts in stages.
|
Good info! Thank you Sir.
__________________
US Air Force Retired
2016 F250 Super Duty - Modified
(Air Bags, Extra Springs, Boxed in Frame, RV Cam, 4.10 Gears) Not your average F250
2022 Cougar 27 SGS
|
|
|
04-26-2021, 02:42 AM
|
#14
|
Member
Join Date: Mar 2016
Location: Swansea Illinois
Posts: 91
|
Quote:
Originally Posted by JRTJH
Using plywood or OSB is IMHO better than using a side from a cardboard box to lay the air conditioner on. There are some "sharp things" around the 14" opening and a cardboard box may not provide all the protection needed. A sheet of plywood or OSB with a towel/moving blanket under it is much harder for that sharp corner to cut through... If it happens to cut through, there's nothing between the "sharp and your TPO roof".....
|
Good point. After looking at the new AC unit, I can certainly see the sharp parts you are referring to. Will definitely use a piece OSB over top of a blanket. Thanks
__________________
US Air Force Retired
2016 F250 Super Duty - Modified
(Air Bags, Extra Springs, Boxed in Frame, RV Cam, 4.10 Gears) Not your average F250
2022 Cougar 27 SGS
|
|
|
04-26-2021, 05:33 AM
|
#15
|
Senior Member
Join Date: Oct 2016
Location: "Murvil, TN
Posts: 2,212
|
I don't have any pictures of this, but I hung a 4 sheave rope hoist in the aluminum tubing using a 3/8" eye bolt.....of my RV Carport....up in the eave of the support truss. I then used a piece of OSB 1/2" thick wood to set the unit on and tied 4 pieces of rope to it, one on each corner, use a bowline knot that I knew would not come loose. I then hoisted the unit up as far as I could get it (a short hook up was necessary) and tied the end of the rope off to keep it there. Then I backed the trailer under the hanging unit and lowered it down on top of the trailer. It worked perfectly and saved my old back a lot of strain. Work smarter, not harder is my motto!
__________________
2016 F350 King Ranch Crew Cab Dually Diesel 4x4
2018 Grand Design Momentum 394M
2023 Suzuki GSX-S1000GT+
Excessive payload capacity is a wonderful thing
"If it ain't Fast....It ain't Fun"
|
|
|
04-29-2021, 07:38 AM
|
#16
|
Junior Member
Join Date: Mar 2014
Location: Central Texas
Posts: 15
|
2d AC
Check the wiring before you get the AC up there. I thought mine was hot and ready for the AC and it was not. Make sure the connectors are correct between the AC and the wiring in the camper. I had to trace back to the fuse panel and put in a new breaker.
2011 Montana Mountaineer
|
|
|
04-29-2021, 09:06 AM
|
#17
|
Senior Member
Join Date: Aug 2013
Location: Tucson
Posts: 822
|
Quote:
Originally Posted by goldtrigger
Check the wiring before you get the AC up there. I thought mine was hot and ready for the AC and it was not. Make sure the connectors are correct between the AC and the wiring in the camper. I had to trace back to the fuse panel and put in a new breaker.
2011 Montana Mountaineer
|
Excellent point. "Pre-wired" doesn't necessarily mean the breaker will be installed and the wires connected in your WFCO power center. If you have to add these, I recommend you run the new AC unit on the "opposite side" of your 50A service. You may need to move some breakers and wires from side to side to accomplish this. But it is good to try to balance the load on each side of your 50A service. Well worth all the work!
Good luck.
|
|
|
04-29-2021, 10:16 AM
|
#18
|
Senior Member
Join Date: Sep 2020
Location: Hot Springs
Posts: 156
|
Quote:
Originally Posted by dwdlt
Good morning All,
I'm going to be installing a second AC on my travel trailer this weekend, and I wanted to reach out to the experts on here to see if you have any specific things I need to watch for?
I have a 2016 Laredo 314RE, it is prewired for the second AC in the bedroom, does have 50 am service that I use often, and the AC unit I bought was the Dometic Brisk Air II, 15k unit.
I did a search on this forum and found a bunch of post about AC units, but none specific enough to provide any detailed "gotcha's" to watch out for.
Any advice provided would be much appreciated.
Thanks
Dale
|
I see you are USAF retired, as am I. When I was active duty I was a jet engine mechanic, or as the AF called it "Aerospace Propulsion Craftsman". Whenever I had to go to the doctor for anything, I'd tell the doc, I won't tell you how to fix people as long as you don't tell me how to fix airplanes and we'll get along fine. That has served me well for over 40 years now. While I'm probably technically competent enough to do this type of install myself, I'd feel better paying someone qualified to do the job and know its done correctly and if I have any issues, I'd have warranty recourse.
Just my 2 cents worth.
__________________
USAF Retired
2018 Ram 2500HD Laramie CTD
2021 Cougar Half Ton 27SABWE
|
|
|
04-29-2021, 10:45 AM
|
#19
|
Member
Join Date: Sep 2014
Location: Colorado Springs, CO
Posts: 35
|
Quote:
Originally Posted by Bandit12
I see you are USAF retired, as am I. When I was active duty I was a jet engine mechanic, or as the AF called it "Aerospace Propulsion Craftsman". Whenever I had to go to the doctor for anything, I'd tell the doc, I won't tell you how to fix people as long as you don't tell me how to fix airplanes and we'll get along fine. That has served me well for over 40 years now. While I'm probably technically competent enough to do this type of install myself, I'd feel better paying someone qualified to do the job and know its done correctly and if I have any issues, I'd have warranty recourse.
Just my 2 cents worth.
|
Bandit, Thanks for your service. I too am USAF retired, aerial surveillance maintenance technician, and 25 years DoD. I've worked on a lot of black box stuff. And, I will agree with your philosophy about not having someone tell me how to fix my stuff. One thing I have learned out in the civilian world, paying someone that is supposedly qualified to do the job doesn't always guarantee it will actually be installed the way you had planned. Just look at how some of the manufacturers installed some of the items in your TT from the factory. Many a times I have gone back and redone stuff that should have been installed better.
|
|
|
04-29-2021, 01:48 PM
|
#20
|
Site Team
Join Date: Mar 2011
Location: Gaylord
Posts: 26,997
|
Quote:
Originally Posted by Farside
Bandit, Thanks for your service. I too am USAF retired, aerial surveillance maintenance technician, and 25 years DoD. I've worked on a lot of black box stuff. And, I will agree with your philosophy about not having someone tell me how to fix my stuff. One thing I have learned out in the civilian world, paying someone that is supposedly qualified to do the job doesn't always guarantee it will actually be installed the way you had planned. Just look at how some of the manufacturers installed some of the items in your TT from the factory. Many a times I have gone back and redone stuff that should have been installed better.
|
The "pitfall" of many people who rely on an RV dealer or on an auto service center is assuming that every technician in the back is competent at every job that business takes on.... Those businesses "will have someone certified to do the job you hire them to do"... The issue comes in when that technician is busy doing another job and the service manager, trying to keep everybody busy, assigns someone who has never done that job and has only a general idea of what to do... That's where any business can get in trouble, assigning someone who has no clue to do a job "ON YOUR TRAILER"....
__________________
John
2015 F250 6.7l 4x4
2014 Cougar X Lite 27RKS
|
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|