|
02-17-2012, 12:29 PM
|
#1
|
Senior Member
Join Date: Apr 2009
Location: WA State
Posts: 250
|
Sewer hose storage
I am wondering what others have done for sewer hose storage on their Alpine? The storage on mine is fairly short compared to my old tt. The Alpine barely holds one length of hose. Any suggestions as for additional storage?
__________________
2012 Keystone Alpine 3500RE
2004.5 CTD 2500
Living the dream in the soggy Northwest!
Always looking for more power, the next add-on goodie, the perfect camping spot, spending more time camping with dw.
|
|
|
02-17-2012, 12:32 PM
|
#2
|
Junior Member
Join Date: Feb 2012
Location: meridian, idaho
Posts: 18
|
I put all sewer hoses and connections in closed container in front storage area. Like you, wasn't thrilled with the sewer hose storage.
|
|
|
02-17-2012, 12:57 PM
|
#3
|
Senior Member
Join Date: Aug 2011
Location: WESTERN,CT
Posts: 2,095
|
MY MONTANA 3750 HAD NO SEWR HOSE STORAGE AT ALL I PUT 2 CAMCO TUBES UNDER THE THE FRONT STORAGE COMPARTMENT. IF YOU GO THAT ROUTE DRILL A FEW HOLE IN THE BOTTOM OF THE TUBE THAT WAY YOU GET DRAINAGE AND AIR FLOW AND NO STINK. BARNEY
__________________
BARNEY AND CHRISTINE
2010 MONTANA 3750FL
2005 DODGE 3500 DUALLY TD
2 RESCUE PUPS: SUSITNA AND CRYSTAL. RIP ALYESKA!
|
|
|
02-17-2012, 01:33 PM
|
#4
|
Senior Member
Join Date: Sep 2011
Location: Northville NY in the Adirondacks
Posts: 2,128
|
The absolute worst place to store stinky slinky is the 4"x4" steel rear bumper. The hose is made of thin plastic over a wire coil. The inside of the bumper begins to rust before you take delivery on it. Metal surface rust is abrasive and will quickly wear holes in the hose as you remove and replace it.
I also use the plastic tote bins for all the bits and pieces that go with the sewer hose as well as the sewer hose itself. When you are done dumping and rinsing, you can throw the hose in the bin, spray in a little bleach water and head for home. When you get home or to your next campsite, you can remove the lid and let it dry out with no odor.
When I dump, I use the lid of the tote to keep the sewer hose off the concrete pad at the dump station. Concrete, like rust, is very abrasive.
__________________
'11 Cougar 326MKS loaded with mods
'12 Ford F250 SuperCab 6.7 PowerStroke Diesel
Amateur Radio: KD2IAT (146.520) GMRS: WQPG808 (462.675 TPL 141.3)
|
|
|
02-17-2012, 02:32 PM
|
#5
|
Senior Member
Join Date: Aug 2010
Location: North Texas
Posts: 1,000
|
Quote:
Originally Posted by turbopilot51
I am wondering what others have done for sewer hose storage on their Alpine? The storage on mine is fairly short compared to my old tt. The Alpine barely holds one length of hose. Any suggestions as for additional storage?
|
Turbopilot51 -
I faced that same question. I got a sewer extension and Camco sewer tube from CW. The tube could open at both ends and the center of the end caps are ventilated. I used some silicon caulk to seal one end but left the vent holes open. Note: I do have the generator prep on my Alpine and have a generator on the starboard of the front compartment. I mounted a L-hook on the port side of the back wall of the front compartment about the same height as the landing gear link. I hung the opening end mount tab of the Camco tube on that hook. Then I scrunched my body in far enough in the door to install an L-hook on the closed end mounting tab at a slightly lower level so the tube hangs at a slight angle - open end up. Now when I need the extension, I just rotate the tube up and it drops out the front compartment. After use, and flush, back into the tube it goes and onto the back wall of the front compartment! The tube is ventilated in the center, so no drips from the lower end.
Ron
__________________
2011 Alpine 3640RL (Beauty)
(Gone! Now replaced by Beauty3)
2016 Ford F-450 (The Beast)
Diesel 4x4, DRW, LB, CC
Comfort Ride Hitch
|
|
|
02-17-2012, 02:59 PM
|
#6
|
Senior Member
Join Date: Jan 2011
Location: Central Florida
Posts: 478
|
I mounted a couple of the white tubes under the front storage compartment, works good for us.
__________________
2011 Chevy Silverado 3500HD Ext Cab LT DRW Duramax/Allison pulling a 2012 SOB (still Thor, but not a Keystone), Dual ACs, 4 Door Fridge, Fireplace, Sleep Number Bed, Level-Up Auto Levelers, Disc Brakes, Winegard DirecTV SlimLine Auto Dish, Onan 5.5K, Splendide Combo Washer/Dryer, GY G114s on HiSpec 17.5 wheels, TrailAir Tri-Glide Pin Box, Mor/ryde IS.
Michelle & Ann Sullivan and 4 American Shorthairs
|
|
|
02-17-2012, 09:14 PM
|
#7
|
Senior Member
Join Date: Apr 2009
Location: WA State
Posts: 250
|
Quote:
Originally Posted by geo
Turbopilot51 -
I faced that same question. I got a sewer extension and Camco sewer tube from CW. The tube could open at both ends and the center of the end caps are ventilated. I used some silicon caulk to seal one end but left the vent holes open. Note: I do have the generator prep on my Alpine and have a generator on the starboard of the front compartment. I mounted a L-hook on the port side of the back wall of the front compartment about the same height as the landing gear link. I hung the opening end mount tab of the Camco tube on that hook. Then I scrunched my body in far enough in the door to install an L-hook on the closed end mounting tab at a slightly lower level so the tube hangs at a slight angle - open end up. Now when I need the extension, I just rotate the tube up and it drops out the front compartment. After use, and flush, back into the tube it goes and onto the back wall of the front compartment! The tube is ventilated in the center, so no drips from the lower end.
Ron
|
Would you share some pics of your setup?
__________________
2012 Keystone Alpine 3500RE
2004.5 CTD 2500
Living the dream in the soggy Northwest!
Always looking for more power, the next add-on goodie, the perfect camping spot, spending more time camping with dw.
|
|
|
02-18-2012, 03:07 AM
|
#8
|
Senior Member
Join Date: May 2011
Location: forked river nj
Posts: 314
|
my cougar has no hose storage. I use pool chlorine bucket. Its 3+ gallons. and looks like a 5 gal bucket but shorter. It has a screw on lid, and seals air tight.
I even put a small piece of pool chlorine table in the bottom, keep it smelling fresh.
When coiled up tight, 2 lengths of flex hose fit.
__________________
2011 F250- gas- 4 star tuner- k&n intake
2011 Cougar 325srx
2015 KTM 350 exc-r
KTM 300 xc-sold
ktm 450 exc-r
|
|
|
02-18-2012, 08:40 AM
|
#9
|
Senior Member
Join Date: Aug 2010
Location: North Texas
Posts: 1,000
|
Quote:
Originally Posted by turbopilot51
Would you share some pics of your setup?
|
Sure. I'll be over there this afternoon and try to post them this evening.
Ron
__________________
2011 Alpine 3640RL (Beauty)
(Gone! Now replaced by Beauty3)
2016 Ford F-450 (The Beast)
Diesel 4x4, DRW, LB, CC
Comfort Ride Hitch
|
|
|
02-18-2012, 05:13 PM
|
#10
|
Member
Join Date: Dec 2011
Location: Roswell, NM
Posts: 74
|
Our Montana HC has hose storage compartment, when I first looked at it, I thought what a waste of space, but......... after further examination it holds 25 feet, no problem. I was surprised. Sells man said it would. But what do they know. Our 2006 Sydney, we had a PVC fence post under trailer for storage of hose. And like round pipe, don't forget the holes.
|
|
|
02-18-2012, 07:47 PM
|
#11
|
Senior Member
Join Date: Aug 2010
Location: North Texas
Posts: 1,000
|
Quote:
Originally Posted by geo
Sure. I'll be over there this afternoon and try to post them this evening.
Ron
|
TurboPilot51 -
Here are the pictures. You can see that I used a shorter L-hook. Be careful because the plywood is only about 1/2 inch, so you cannot screw it in too deep. I used short eye screws and a short bungee cord to secure it to the wall so it doesn't bounce around. You can see the rotating bar for the front landing gear in the picture, and from that you can see that the hose tube is at a slight angle to it. That way, a rinsed sewer hose that has been shaked dry while connected to the disposal dump, can be stored within the tube and allowed to dry slowly via the vents.
While you are in the front compartment, look up! The chipboard you see is the floorboard of the bedroom under the bed! After discovering this today, I plan to use some styrofoam insulation sheets to insulate this area. That way, I can cut the foam to fit, glue it to the rectagular beams and leave a channel for the hydralics and electrical, and use some non-expanding foam to seal the starboard end.
Let me know what you think!
Ron
__________________
2011 Alpine 3640RL (Beauty)
(Gone! Now replaced by Beauty3)
2016 Ford F-450 (The Beast)
Diesel 4x4, DRW, LB, CC
Comfort Ride Hitch
|
|
|
02-19-2012, 08:00 AM
|
#12
|
Senior Member
Join Date: Apr 2009
Location: WA State
Posts: 250
|
Quote:
Originally Posted by geo
TurboPilot51 -
Here are the pictures. You can see that I used a shorter L-hook. Be careful because the plywood is only about 1/2 inch, so you cannot screw it in too deep. I used short eye screws and a short bungee cord to secure it to the wall so it doesn't bounce around. You can see the rotating bar for the front landing gear in the picture, and from that you can see that the hose tube is at a slight angle to it. That way, a rinsed sewer hose that has been shaked dry while connected to the disposal dump, can be stored within the tube and allowed to dry slowly via the vents.
While you are in the front compartment, look up! The chipboard you see is the floorboard of the bedroom under the bed! After discovering this today, I plan to use some styrofoam insulation sheets to insulate this area. That way, I can cut the foam to fit, glue it to the rectagular beams and leave a channel for the hydralics and electrical, and use some non-expanding foam to seal the starboard end.
Let me know what you think!
Ron
|
Thanks for the pics Geo! I am still learning where stuff is on my rig and a little hesitant drilling holes yet. The stock hose storage tube would better work if it were about two foot longer. There is a frame piece that sticks out that keeps me from installing a longer tube. For now I will just use a plastic storage bin to store the hoses.
__________________
2012 Keystone Alpine 3500RE
2004.5 CTD 2500
Living the dream in the soggy Northwest!
Always looking for more power, the next add-on goodie, the perfect camping spot, spending more time camping with dw.
|
|
|
02-19-2012, 01:47 PM
|
#13
|
Senior Member
Join Date: Jan 2011
Location: Sherwood Park (Edmonton), Alberta, Canada
Posts: 173
|
My problem is that none of these storage "tubes" will fit the fittings on the Rhino hose.
__________________
2011 Keystone Alpine 3500RE w/ Trail Air Tri-Glide
2011 GMC Sierra Denali 3500HD SRW B&W Turnover Ball w/ 5th Wheel Companion
|
|
|
02-27-2012, 05:20 PM
|
#14
|
Junior Member
Join Date: Feb 2012
Location: Sweetwater TX.
Posts: 2
|
Quote:
Originally Posted by X-Treme
My problem is that none of these storage "tubes" will fit the fittings on the Rhino hose.
|
Yes indeed, I have found this out the hard way.
|
|
|
02-27-2012, 08:22 PM
|
#15
|
Senior Member
Join Date: Aug 2010
Location: Dacula, GA
Posts: 620
|
Sewer hose "storage"
Not a problem if you don't use one Just throw it away and every 3 days open all valves and drive like h*** . That way you NEVER have to worry about storage..
p.s.: never return to the same camp spot
|
|
|
02-28-2012, 04:40 AM
|
#16
|
Senior Member
Join Date: Sep 2011
Location: Northville NY in the Adirondacks
Posts: 2,128
|
Over on the Sunline Club, there are several threads from folks that made up their own carriers for the Rhino hoses using PVC fence post material. Here's one with pics:
http://www.sunlineclub.com/forums/f6...ier-11723.html
__________________
'11 Cougar 326MKS loaded with mods
'12 Ford F250 SuperCab 6.7 PowerStroke Diesel
Amateur Radio: KD2IAT (146.520) GMRS: WQPG808 (462.675 TPL 141.3)
|
|
|
02-28-2012, 06:05 AM
|
#17
|
Senior Member
Join Date: May 2010
Location: Plymouth,Ia
Posts: 109
|
I made mine from a plastic fence post like was listed on the post. I mounted it under the frame in front of the tires next to the dump valve. Somewhere around $20.00 for the post and end caps.
__________________
2010 2500HD LTZ Duramax
2010 Cougar 327RES
|
|
|
02-28-2012, 08:13 AM
|
#18
|
Senior Member
Join Date: Dec 2011
Location: Whittier, Ca
Posts: 181
|
I just bought the premade pipe sold at CW. I was going to make my own out of 5" or 6" abs/pvc but its hard to find and expensive. I looked at the fence post at Home Depot and its expensive also. SO for the ease of the project I just bought the premade pipe. It came out about the same price.
I dont have the rhino hose and connections. My 5th came with the cheap hoses which are fine for know. While at CW I checked most of the better hoses and fittings and they all fit except the 90* fittings. I think when I buy new better quality hoses I'll just live without the 90*. As long as the fittings have quick adapters I can store them in a case to use if needed.
Jerry
__________________
Jerry
2008 Keystone Springdale 242FWRLSSR 5th wheel
2011 Chevy 2500 6.0 gas
16K Super Glide Sliding Hitch
|
|
|
02-28-2012, 08:52 AM
|
#19
|
Senior Member
Join Date: Mar 2011
Location: Pearl River, La.
Posts: 198
|
What size works best - 5" or 6"?
__________________
2011 Toyota Tundra - (MGM) Mean Green Machine
2012 Cougar HC 291RLS - Cajun Riviera
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|