|
01-24-2021, 12:48 PM
|
#1
|
Junior Member
Join Date: Jan 2021
Location: Montreal
Posts: 6
|
Help! Hitch Height for mini
I just bought a 2016 Sprindale summerland mini 1800BH. I have a Subaru ascent with a 24 in hitch height. The trailer is currently stored far from home so I cannot measure hitch height. I need to buy the proper hitch receiver to pick it up. Anyone know what the hitch height is on the summerland mini?
|
|
|
01-24-2021, 01:24 PM
|
#2
|
Site Team
Join Date: Jul 2014
Location: Modesto
Posts: 20,339
|
Welcome to the forum
Your Ascent receiver is 24” from the ground?
The most common height for the ball on trailers that size is 20-22” from the ground. Without knowing the weight of the trailer tongue, it may squat your car so it’s hard to say what shank you might need. Also need to know if the ball is 2” or 2 5/16”.
__________________
2012 Copper Canyon 273FWRET being towed by a 1994 Ford F350 CC,LB,Dually diesel.
Airlift 5000 bags, Prodigy brake control, 5 gauges on the pillar.Used to tow a '97 Jayco 323RKS.
Now an RVIA registered tech. Retired from Law enforcement in 2008 after 25+ yrs.
|
|
|
01-24-2021, 01:28 PM
|
#3
|
Site Team
Join Date: Oct 2011
Location: Joppa, MD
Posts: 11,750
|
Quote:
Originally Posted by Jalex
I just bought a 2016 Sprindale summerland mini 1800BH. I have a Subaru ascent with a 24 in hitch height. The trailer is currently stored far from home so I cannot measure hitch height. I need to buy the proper hitch receiver to pick it up. Anyone know what the hitch height is on the summerland mini?
|
First welcome to the forum. Did you by chance take a look at your Subaru'
s payload sticker? You can find it on the drivers side door jamb. It will be a yellow and white sticker that bsya "tire inflation guide" and printed on it will be "All passengers and cargo shall not exceed xxx lbs." that's the payload capacity. Alsi look on the hitch itself or in the drivers handbook for the hitch capacity which likely will be 500 lbs. max.
I think that Subaru is a unibody not a full frame SUV so you cannot use a weight distributing hitch. The trailer's max weight is 3,940 lbs. which you will be close to when loaded for camping. Hitch weight is typically calculated at 13% of trailer GVWR when the actual weight is not known. If you multiply the 3,.940 by .13 (13%) then the ESTIMATED tongue weight will be 512 lbs.
Take that max load capacity number and subtract the tongue weight, the weight of the witch and the weight of your family and everything that you have added to or put into the vehicle. I'm guessing you'll be over your payload. Small SUVs like that are not meant to tow 21' campers. That camper will push that SUV around in the wind or when a large truck passes.
I'm not trying to dampen your enthusiasm but ,merely making you aware of what you are facing and looking for you and your family to have an enjoyable and safe experience. It's no fun to drive "white knuckled" to get to a campground.
__________________
Marshall
2012 Laredo 303 TG
2010 F250 LT Super Cab, long bed, 4X4, 6.4 Turbo Diesel
|
|
|
01-24-2021, 01:36 PM
|
#4
|
Junior Member
Join Date: Jan 2021
Location: Montreal
Posts: 6
|
Thanks. Ascent payload is 1158 lbs sont i will be close but will manage rv and vehicle load accordingly. I just bought everything so i will need to make it work i guess. I also bought a tongue scale to stay below 500 lbs tongue weight. I will also never travel with water in the tanks.
|
|
|
01-24-2021, 01:37 PM
|
#5
|
Junior Member
Join Date: Jan 2021
Location: Montreal
Posts: 6
|
Quote:
Originally Posted by chuckster57
Welcome to the forum
Your Ascent receiver is 24” from the ground?
The most common height for the ball on trailers that size is 20-22” from the ground. Without knowing the weight of the trailer tongue, it may squat your car so it’s hard to say what shank you might need. Also need to know if the ball is 2” or 2 5/16”.
|
Thanks. Ball size is 2 5/16.
|
|
|
01-24-2021, 03:30 PM
|
#6
|
Site Team
Join Date: Feb 2014
Location: W. Texas
Posts: 17,685
|
Something is wrong or I got cheated on my new 1 ton, 4 wheel drive Ram; the bottom of my receiver is 21" off the ground.......
Looking at the pics of the Ascent you either have a custom made receiver that pops up behind the back hatch door OR....that receiver might be 12" off the ground - maybe.
__________________
Danny and Susan, wife of 56 years
2019 Ram 3500 Laramie CC SWB SB 6.4 4x4 4.10
2020 Montana High Country 331RL
|
|
|
01-24-2021, 05:49 PM
|
#7
|
Junior Member
Join Date: Jan 2021
Location: Montreal
Posts: 6
|
There is a pop up hiding the ascent hitch. Its 24 inches off the ground which i find a bit high....
|
|
|
01-24-2021, 06:09 PM
|
#8
|
Site Team
Join Date: Jul 2014
Location: Modesto
Posts: 20,339
|
If it we’re meeting, I would get a straight shank. The trailer is going to squat the back end and if I’m close to the ball height, it should tow just about level.
I see your in Canada, so I don’t know if you have stores like Lowe’s or Home Depot, but if you do, they sell a variety of shanks so you could change it out quickly. Another though that just popped into my mind-what size is the receiver?
Hopefully it’s 2”X2”.
__________________
2012 Copper Canyon 273FWRET being towed by a 1994 Ford F350 CC,LB,Dually diesel.
Airlift 5000 bags, Prodigy brake control, 5 gauges on the pillar.Used to tow a '97 Jayco 323RKS.
Now an RVIA registered tech. Retired from Law enforcement in 2008 after 25+ yrs.
|
|
|
01-24-2021, 06:16 PM
|
#9
|
Junior Member
Join Date: Jan 2021
Location: Montreal
Posts: 6
|
Yes its a 2x2. I am trying to figure out the right drop as I think the ascent is high a 24 inch. If the 2016 mini is at 16 that would require a 8inch drop. Suraru oem shank is 6inch drop. Yes likely home depot, lowes or Canadian tire (if you happen to travel to canada this is a good place to shop for this)
|
|
|
01-24-2021, 06:26 PM
|
#10
|
Site Team
Join Date: Jul 2014
Location: Modesto
Posts: 20,339
|
Quote:
Originally Posted by Jalex
Yes its a 2x2. I am trying to figure out the right drop as I think the ascent is high a 24 inch. If the 2016 mini is at 16 that would require a 8inch drop. Suraru oem shank is 6inch drop. Yes likely home depot, lowes or Canadian tire (if you happen to travel to canada this is a good place to shop for this)
|
You do want to start with the ball about 2-3” higher than the hitch to allow for the frame to drop.
__________________
2012 Copper Canyon 273FWRET being towed by a 1994 Ford F350 CC,LB,Dually diesel.
Airlift 5000 bags, Prodigy brake control, 5 gauges on the pillar.Used to tow a '97 Jayco 323RKS.
Now an RVIA registered tech. Retired from Law enforcement in 2008 after 25+ yrs.
|
|
|
01-24-2021, 08:50 PM
|
#11
|
Junior Member
Join Date: Jan 2021
Location: Montreal
Posts: 6
|
Quote:
Originally Posted by chuckster57
You do want to start with the ball about 2-3” higher than the hitch to allow for the frame to drop.
|
Thanks. That’s helpful.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|