|
08-26-2020, 09:18 AM
|
#1
|
Junior Member
Join Date: Aug 2020
Location: BANGOR
Posts: 1
|
TV Cable issue
Sorry for the long post... Recently bought a used 2020 Springdale 298BH, our first ever travel trailer. At our first campsite we connected the site's cable TV to the outside jack at the rear of the trailer, but the TV signal would not work (I had it connected to the powered antenna jack and the powered antenna was turned off, as required). As a noobie, I also tried connecting the TV to each of the other 2 coax connectors (the ones connected to each other by a U-shaped jumper), but neither of those worked, either. So I gave up and thought it was the site's cable that didn't work. We went to another site last week and had the same issue, so I removed the powered coax plate from the wall to see what was going on. See Image1 for what I found. Yes, that short orange cable is not connected to anything, and there's an unused coax connector on the back of the circuit board. So to get a better feel for the connections, I removed the dual coax plate as well and...well, see for yourself in Image2... Seriously? Wow! So I started pulling on the cables in the wall and found that the orange cable in the wall (Image2) was spliced to the grey cable (image1). By dumb luck, I decided to try something...I connected the TV to the coax in the bunkhouse and it worked! So while the TV was on, I disconnected the orange and grey cables from one another and the signal was lost. That told me that one of them was the live signal, so I guessed that it was the grey cable and connected it to the open connection on the circuit board, then spliced together the 2 orange cables. That worked! The main TV location, the bunkhouse and the bedroom TVs now all worked. I forgot to try the outside TV connection, though, so I'll try that in a couple weeks, BUT the point of all of this is - what should that dual coax plate be connected to?? I don't even see any other loose cables in the wall near the plate to connect to it. From what I've gathered, those are supposed to be used for satellite hookups, so does that mean my trailer is not wired properly for satellite? I'm completely dumbfounded by this wiring job! I mean, how exactly does something like this pass through the factory? Didn't the person who screwed the plate to the wall, ya know, not notice it wasn't connected to anything?? Ridiculous! Anyway, is there maybe a wiring schematic out there that could help me understand how things should be wired? Thanks!
|
|
|
08-26-2020, 09:43 AM
|
#2
|
Senior Member
Join Date: Jul 2013
Location: Box Elder
Posts: 2,899
|
This tool will be your friend when it comes to the coax cabling in these rigs. There are no schematics for anything in these RV's, electric, plumbing, or coax.
https://www.amazon.com/Locations-Exp...62&s=hi&sr=1-4
__________________
Bob & Becky
2012 3402 Montana
2012 Chevy 2500HD D/A CC
|
|
|
08-26-2020, 11:25 AM
|
#3
|
Senior Member
Join Date: Nov 2017
Location: Picacho, Az
Posts: 6,809
|
Quote:
Originally Posted by wmg101
Sorry for the long post... Recently bought a used 2020 Springdale 298BH, our first ever travel trailer. At our first campsite we connected the site's cable TV to the outside jack at the rear of the trailer, but the TV signal would not work (I had it connected to the powered antenna jack and the powered antenna was turned off, as required). As a noobie, I also tried connecting the TV to each of the other 2 coax connectors (the ones connected to each other by a U-shaped jumper), but neither of those worked, either. So I gave up and thought it was the site's cable that didn't work. We went to another site last week and had the same issue, so I removed the powered coax plate from the wall to see what was going on. See Image1 for what I found. Yes, that short orange cable is not connected to anything, and there's an unused coax connector on the back of the circuit board. So to get a better feel for the connections, I removed the dual coax plate as well and...well, see for yourself in Image2... Seriously? Wow! So I started pulling on the cables in the wall and found that the orange cable in the wall (Image2) was spliced to the grey cable (image1). By dumb luck, I decided to try something...I connected the TV to the coax in the bunkhouse and it worked! So while the TV was on, I disconnected the orange and grey cables from one another and the signal was lost. That told me that one of them was the live signal, so I guessed that it was the grey cable and connected it to the open connection on the circuit board, then spliced together the 2 orange cables. That worked! The main TV location, the bunkhouse and the bedroom TVs now all worked. I forgot to try the outside TV connection, though, so I'll try that in a couple weeks, BUT the point of all of this is - what should that dual coax plate be connected to?? I don't even see any other loose cables in the wall near the plate to connect to it. From what I've gathered, those are supposed to be used for satellite hookups, so does that mean my trailer is not wired properly for satellite? I'm completely dumbfounded by this wiring job! I mean, how exactly does something like this pass through the factory? Didn't the person who screwed the plate to the wall, ya know, not notice it wasn't connected to anything?? Ridiculous! Anyway, is there maybe a wiring schematic out there that could help me understand how things should be wired? Thanks!
|
You won't find schematics for any of the systems from Keystone, some of the forum members may found some, but for the most part they are top secret.
You're lucky to have found your issue & the splitter was easily found, some are hidden in walls or ceilings.
__________________
Full-timed 10+ years
Sold '13 Redwood FB
Traded '13 GMC Denali DRW D/A
Replacement undetermined
|
|
|
08-26-2020, 11:33 AM
|
#4
|
Senior Member
Join Date: Jul 2011
Location: So. Cal
Posts: 169
|
You bought a used trailer. I’m guessing it might’ve been hooked up correctly when new from the factory, but possibly the previous owner did some coax work and wall plates to fit their needs and that’s what you ended up with. Previous owner then removed items they wanted before selling/trade-in and threw it back together not caring if it worked or not.
Glad you’re getting it sorted out.
__________________
Rick
2016 Springdale 212RB
2001 Ford F-250 Super Duty 7.3 Diesel <100K
|
|
|
08-26-2020, 01:36 PM
|
#5
|
Site Team
Join Date: Oct 2011
Location: Joppa, MD
Posts: 11,714
|
Download the Sensor Pro instructions here https://winegard.com/industry/recrea...sesarpro-black
The cable to TV 1 or 2 (whichever is the front TV typically) goes to the plate with the 2 coax connectors, one in from Amp and one out to TV. The coax loop on the front just connects it when no satellite receiver is used.
My guess previous owner probably had a dish and wanted fewer coax connections and did some DIY work.
__________________
Marshall
2012 Laredo 303 TG
2010 F250 LT Super Cab, long bed, 4X4, 6.4 Turbo Diesel
|
|
|
12-26-2020, 07:53 PM
|
#6
|
Junior Member
Join Date: Dec 2020
Location: Charlotte
Posts: 2
|
I hope your cable issue is resolved. I want to ask a quick question. I have just purchased a 2021 298BH and wanted to know if you have found sheets to fit the bunks. Thanks!
|
|
|
|
Thread Tools |
|
Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|