|
12-12-2018, 10:03 AM
|
#1
|
Member
Join Date: Dec 2018
Location: Clarkston
Posts: 51
|
Repair question
Forgive me if I use wrong terminology...
I need to replace the screw cover trim but while I was checking the end cap of the trim, I noticed where the screw goes into the side/edge of the TT that he hole is stripped out and the screw spins freely. In my house when I notice something similar, say in my kitchen cabinets, I drill out the stripped hole to 1/4" diameter and glue a 1/4" hardwood dowel in and the screw holds. Can similar be done on an RV with the thin walls? How do you deal with stripped ou screw holes?
|
|
|
12-12-2018, 10:11 AM
|
#2
|
Senior Member
Join Date: May 2016
Location: South Jordan, Utah
Posts: 2,223
|
I've inserted wooden match sticks into the existing hole with a fair amount of silicone sealant. Let dry, then the original screw with more sealant on top. so far so good
__________________
2017 Cougar 279RKSWE
2007.5 Dodge Ram 2500 6.7 Cummins
Retirement Training Completed
I think the little voices in my head have started a chat group.
|
|
|
12-12-2018, 10:29 AM
|
#3
|
Member
Join Date: Dec 2018
Location: Clarkston
Posts: 51
|
Quote:
Originally Posted by Canonman
I've inserted wooden match sticks into the existing hole with a fair amount of silicone sealant. Let dry, then the original screw with more sealant on top. so far so good
|
Thank you. I am nervous about drilling into the walls. Your idea does make sense as it is less invasive.
|
|
|
12-12-2018, 11:28 AM
|
#4
|
Senior Member
Join Date: Oct 2018
Location: Southern California
Posts: 1,286
|
I have noticed a lot of those screws are very susceptible to over tightening which will strip it out very quickly. I always tighten by hand and only to snug.
__________________
Mike
2017 F250 6.7 Powerstroke FX4 crew cab
2016 Hideout 24BHSWE (27 foot TT)
|
|
|
12-12-2018, 12:51 PM
|
#5
|
Member
Join Date: Dec 2018
Location: Clarkston
Posts: 51
|
Quote:
Originally Posted by Logan X
I have noticed a lot of those screws are very susceptible to over tightening which will strip it out very quickly. I always tighten by hand and only to snug.
|
Right. I removed some curtain clips and found they were easily turned with the bit in my fingers.
What about Lock-Tite, especially on exterior screws?
|
|
|
12-12-2018, 01:50 PM
|
#6
|
Site Team
Join Date: Feb 2014
Location: W. Texas
Posts: 17,677
|
Exterior screws go into all sorts of materials. I use Loctite on screws going into/through metal then back them with speed nuts. I use washers under the screws in the fenders because they will split and break if you're not careful (along with the speednuts). I've never used Loctite on screws going into wood.
__________________
Danny and Susan, wife of 56 years
2019 Ram 3500 Laramie CC SWB SB 6.4 4x4 4.10
2020 Montana High Country 331RL
|
|
|
12-12-2018, 02:28 PM
|
#7
|
Member
Join Date: Dec 2018
Location: Clarkston
Posts: 51
|
Quote:
Originally Posted by sourdough
Exterior screws go into all sorts of materials. I use Loctite on screws going into/through metal then back them with speed nuts. I use washers under the screws in the fenders because they will split and break if you're not careful (along with the speednuts). I've never used Loctite on screws going into wood.
|
Right. I wouldn't use Lock-Tite on wood. I'm talking where metal meets metal.
|
|
|
12-12-2018, 02:43 PM
|
#8
|
Senior Member
Join Date: Nov 2017
Location: Sacramento
Posts: 187
|
Quote:
Originally Posted by Canonman
I've inserted wooden match sticks into the existing hole with a fair amount of silicone sealant. Let dry, then the original screw with more sealant on top. so far so good
|
Does silicone sealant put out the fire when you drill into that "strike anywhere" head?
I've used toothpicks in similar situations because they appear (to me anyways) more stout than match stick wood. I'm sure good ol' Diamond matchsticks work well too. Just be sure to trim that red end first.
__________________
Number 4: 2013 Hideout 19FLBWE
Number 3: 1994 Skyline Nomad 1661
Number 2: 1971 Santa Fe
Number 1: 1967 Shasta Airflyte
2015 F-250 Lariat 6.2L CC 4x4 3.73
|
|
|
12-12-2018, 03:17 PM
|
#9
|
Senior Member
Join Date: May 2016
Location: South Jordan, Utah
Posts: 2,223
|
Quote:
Originally Posted by Number 4
Does silicone sealant put out the fire when you drill into that "strike anywhere" head?
I've used toothpicks in similar situations because they appear (to me anyways) more stout than match stick wood. I'm sure good ol' Diamond matchsticks work well too. Just be sure to trim that red end first.
|
You put the wood end in the hole then light the head so you can see where the screw goes I thought everyone knew that trick
__________________
2017 Cougar 279RKSWE
2007.5 Dodge Ram 2500 6.7 Cummins
Retirement Training Completed
I think the little voices in my head have started a chat group.
|
|
|
12-12-2018, 05:50 PM
|
#10
|
Senior Member
Join Date: Oct 2018
Location: Southern California
Posts: 1,286
|
Quote:
Originally Posted by Canonman
You put the wood end in the hole then light the head so you can see where the screw goes I thought everyone knew that trick
|
Just like Rambo when he cauterized a wound with gun powder. Haha
__________________
Mike
2017 F250 6.7 Powerstroke FX4 crew cab
2016 Hideout 24BHSWE (27 foot TT)
|
|
|
12-12-2018, 06:39 PM
|
#11
|
Site Team
Join Date: Oct 2011
Location: Joppa, MD
Posts: 11,743
|
Quote:
Originally Posted by Canonman
You put the wood end in the hole then light the head so you can see where the screw goes I thought everyone knew that trick
|
For larger holes use road flares.
__________________
Marshall
2012 Laredo 303 TG
2010 F250 LT Super Cab, long bed, 4X4, 6.4 Turbo Diesel
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
All times are GMT -8. The time now is 07:05 PM.