|
02-27-2018, 06:41 AM
|
#1
|
Senior Member
Join Date: May 2015
Location: Near Saratoga Springs,
Posts: 1,131
|
Two propane regulators on newer units
I made a discovery yesterday!
If you have two propane bottles and they are separated by 60 inches or more, you are required to have a step down, 30 psig output regulator, usually on the curbside bottle**.
OK, with that said, I had a problem last fall where I lost feed from that regulated bottle which was far from empty. I have a new two stage auto change over regulato to install but want to do both but would like a manufacturer and a part number if anyone has it available - that step down regulator is in a tight spot to see without pulling it out. Of course, I could just eliminate that step down regulator too, but ..... see below
**FYI : The NFPA 1192 Standard on Recreational Vehicles says:
"5.3.11.2 Propane system pressure shall be regulated to a pressure of 30 psi (207 kpa) or less within 60 in. (1.5m) of the container outlet."
|
|
|
02-27-2018, 07:26 AM
|
#2
|
Site Team
Join Date: Mar 2011
Location: Gaylord
Posts: 26,997
|
Any RV dealership will have the step-down or "high pressure" regulator in stock. That regulator does more than just "sit there because it's required by code"... Here is one thread that discusses it fairly well: http://www.keystoneforums.com/forums...step+regulator Check bobbecky's post #6, he explains why it's there in good, easy to understand terms.
__________________
John
2015 F250 6.7l 4x4
2014 Cougar X Lite 27RKS
|
|
|
02-27-2018, 08:13 AM
|
#3
|
Senior Member
Join Date: Nov 2017
Location: Picacho, Az
Posts: 6,809
|
Replace both step down & changeover with Marshall brand regulators. The cheap Chinese regulators that came originally are junk.
__________________
Full-timed 10+ years
Sold '13 Redwood FB
Traded '13 GMC Denali DRW D/A
Replacement undetermined
|
|
|
02-27-2018, 08:22 AM
|
#4
|
Senior Member
Join Date: Nov 2017
Location: Picacho, Az
Posts: 6,809
|
__________________
Full-timed 10+ years
Sold '13 Redwood FB
Traded '13 GMC Denali DRW D/A
Replacement undetermined
|
|
|
02-27-2018, 08:54 AM
|
#5
|
Senior Member
Join Date: May 2015
Location: Near Saratoga Springs,
Posts: 1,131
|
John - Please fully read what my OP said as your response reads like you really haven't
I have read the author's linked post both here and his MOC thread and intend on replacing the suspect item
This is not an inflated price RV stealership parts department item but a simple Marshal Excelsior, MB Sturgis or even a Camco or similar branded 10 buck item
Back to my original question - does anyone have a part number. If not, then I'll pull the existing one off and go from there
|
|
|
02-27-2018, 09:17 AM
|
#6
|
Site Team
Join Date: Mar 2011
Location: Gaylord
Posts: 26,997
|
Quote:
Originally Posted by Dave W
I made a discovery yesterday!
If you have two propane bottles and they are separated by 60 inches or more, you are required to have a step down, 30 psig output regulator, usually on the curbside bottle**.
OK, with that said, I had a problem last fall where I lost feed from that regulated bottle which was far from empty. I have a new two stage auto change over regulato to install but want to do both but would like a manufacturer and a part number if anyone has it available - that step down regulator is in a tight spot to see without pulling it out. Of course, I could just eliminate that step down regulator too, but ..... see below
**FYI : The NFPA 1192 Standard on Recreational Vehicles says:
"5.3.11.2 Propane system pressure shall be regulated to a pressure of 30 psi (207 kpa) or less within 60 in. (1.5m) of the container outlet."
|
Dave W,
I did read your original post "FULLY" and was responding to the part that I highlighted in RED above. Since I don't have separated propane tanks, I don't have the high pressure regulator, but if I did, rest assured that I'd rush right out there in the cold and get the numbers for you.... Yeah, I know...
Anyway, I do hope you find the part numbers you need. You might try looking at the Trekwood site. I'm sure it's listed by part number/nomenclature there. Alternatively, you can always use Google to find a Marshall 30# high pressure regulator or even walk out and take the defective one out of your trailer to get the "exact numbers" from your specific regulator...
My comment was intended to offer a suggestion NOT to bypass or eliminate that regulator, it does serve a purpose. Of course, if you so choose to do just that, it'd would be perfectly fine with me. Hope you have a "wunnerful day" after unloading
__________________
John
2015 F250 6.7l 4x4
2014 Cougar X Lite 27RKS
|
|
|
02-27-2018, 10:21 AM
|
#7
|
Senior Member
Join Date: May 2015
Location: Near Saratoga Springs,
Posts: 1,131
|
The existing regulator was a Fairview GB-630, a brand which I have never heard of. It is being replaced by a Marshall Excelsior MEGR 130-30 along with a new 20" pigtail. The two stage on the other side is also being replaced by a Marshall, p/n MEGR 253.
The new single stage regulator and hose are on order from RV Upgrades and a couple bucks, even with shipping. cheaper then AMAZON plus I like to give a smaller company my business if possible vs AMAZON that didn't pay a nickle in US taxes last year.
The Fairview is a 100 pound input vs a 250 pound input for the Marshall. The Fairview has a 500,000 Btu output vs 1.2 million for the Marshall
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|