|
12-10-2014, 08:19 PM
|
#1
|
Junior Member
Join Date: Dec 2014
Location: Eloy, AZ
Posts: 3
|
Lost electric power to slide out wall outlet, overhead light, etc.
No power, AC or 12 volt to wall outlet, overhead light, and wall lamp, all in the living room slide out. Breaker did not trip. Breaker had tripped two times before last year. Could it be a bad breaker? Appreciate any suggestions.
|
|
|
12-10-2014, 08:34 PM
|
#2
|
Senior Member
Join Date: Apr 2011
Location: Arrey,
Posts: 2,368
|
bearskin, Howdy;
Check under the slide to see if the wires are intact the slide may have
damaged them when it was cycled.
Under my slide is a junction box, looks like a single wall switch box with a
solid cover, the wires come out and are suspended by a spring arrangement
then enter the box then up into the slide. It's a starting point...
hankaye
__________________
Striving for a less complicated life since 1949 ...
Home: 2008 Cougar 278 RKS
T.V.: 2004 F-250 4X4, Level III BulletProofed , Detroit Tru-Track Differential (915A550)
Dog: 2006 Border Collie (Rascal) aka Maximum fur dispersal unit. (08/04/2006 - 12/16/2017) RIP.
|
|
|
12-11-2014, 02:23 AM
|
#3
|
Senior Member
Join Date: Mar 2010
Posts: 452
|
Hankaye has the answer, the constant bending of those wires as the slide out extends and retracts takes its toll on them.
I lost the DC overhead light once and could never find where the wire broke, I'm assuming the break was deep behind the J panel where it enters the basement. I said the heck with it and wired in a 110 AC lamp in to the junction box under the slide. So now that lamp is AC :-)
Ron W.
__________________
2019 Cougar 25RLS
03 Dodge 2500 Cummins
Disc brakes
700 watts solar
2000 watt inverter
|
|
|
12-11-2014, 08:33 AM
|
#4
|
Junior Member
Join Date: Aug 2013
Location: louisville ky
Posts: 5
|
Check to see if you your battery is dead. Even if plugged in can still cause problems.
|
|
|
12-11-2014, 09:12 AM
|
#5
|
Site Team
Join Date: Mar 2011
Location: Gaylord
Posts: 26,997
|
Quote:
Originally Posted by bearskin
No power, AC or 12 volt to wall outlet, overhead light, and wall lamp, all in the living room slide out. Breaker did not trip. Breaker had tripped two times before last year. Could it be a bad breaker? Appreciate any suggestions.
|
The wall outlet is 120 VAC and the overhead lights/wall lamp are 12VDC. There are two separate wiring circuits into the slide, one for "shore power" (120VAC) and another wiring circuit for "battery/converter power" (12VDC). It would seem unlikely that both wiring circuits would fail at the same time (from flexing/wire fatigue) unless there was some damage to the wiring bundle under the trailer. It should exit the trailer floor at a junction box, then enter the slide at another junction box. The wiring harness between the two boxes is likely the problem area. As I said, it's unlikely both would simply fail at the same time, so there is probably damage to the harness. It could easily get caught on something during extension or retraction of the slide or even get hung on a shrub or tree branch if you've recently moved your RV.
I would crawl under the trailer and check the wiring harness for damage. Keep in mind that if there is damage and you're plugged into shore power, you could have exposed 120 volt wiring. Proceed with some caution, unplug your trailer and crawl under it. Chances are you'll find the harness either pulled out of a junction box or cut/broken somewhere between the trailer and the slide.
Good Luck.
__________________
John
2015 F250 6.7l 4x4
2014 Cougar X Lite 27RKS
|
|
|
12-11-2014, 01:10 PM
|
#6
|
Site Team
Join Date: Jul 2014
Location: Modesto
Posts: 20,357
|
If I can add: inside the J boxes, factory loves to use wire nuts on 120, seen a few backed off. If that's the case, screw them back tight and then secure with electrical tape.
__________________
2012 Copper Canyon 273FWRET being towed by a 1994 Ford F350 CC,LB,Dually diesel.
Airlift 5000 bags, Prodigy brake control, 5 gauges on the pillar.Used to tow a '97 Jayco 323RKS.
Now an RVIA registered tech. Retired from Law enforcement in 2008 after 25+ yrs.
|
|
|
12-11-2014, 03:49 PM
|
#7
|
Member
Join Date: Jul 2014
Location: Crossville, TN
Posts: 61
|
Slide Power
Check the wiring from the basement out to the slide wall. It's held up by springs. 120v and 12v are all wrapped together on my Everest. Last time out, I connected to shore power before extending the slides. 120v had a short and I saw the spark shooting out under the slide.
|
|
|
12-11-2014, 05:03 PM
|
#8
|
Site Team
Join Date: Jun 2009
Location: Venice
Posts: 5,346
|
In the inside corner of the slide, possibly inside a bench if you have a booth. There should be a plastic box similar to the photo below. (most likely black .. I painted this one when I added the surface mount outlet) Behind that cover you will find a terminal block where Keystone in all it's wisdom has connected both low and high voltage with the same device. When I had the same problem I checked the J cord under the slide first (the one with the spring) and then found my loose connections at the terminal block inside that box. Good luck with your search, Hank
__________________
Hank & Lynn
2007 Cougar 290RKS, E-Z Flex, 16" XPS RIBs ( SOLD .. Gonna miss her ... looking for new 5r)
2004.5 Dodge 2500 QC, LB, 5.9HO, WestTach gauges, Ride-Rite
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|