|
05-11-2014, 10:01 AM
|
#1
|
Junior Member
Join Date: May 2014
Location: NJ
Posts: 12
|
Awning wiring for Passport 285RL
It seems I have no power from my switch to the awning. I have power to the switch and leaving the switch but somewhere there is a splice. The wire from the awning and from the switch are different. Does anyone know where the splice is located?
|
|
|
05-11-2014, 01:59 PM
|
#2
|
Senior Member
Join Date: May 2010
Location: Rochester, NY
Posts: 1,605
|
Hi. I had a similar issue on my unit when it was brand new. On mine, there was a solid state relay hanging in the bees nest of wires behind the control panel that was defective. The relay is black, about 2.5" long by 3/4" wide by 1/2 thick. This condition allowed power past the switch but not through the relay which powers the awning motor. I had the relay replaced under warranty. I was able to get the awning to open and close by manually using jumper wires and bypassing the relay while I waited for the relay to arrive. It was an easy fix.
I have photos if you need them.
|
|
|
05-11-2014, 04:28 PM
|
#3
|
Junior Member
Join Date: May 2014
Location: NJ
Posts: 12
|
Yes pictures would help a lot. Thank you!!
|
|
|
05-11-2014, 04:29 PM
|
#4
|
Junior Member
Join Date: May 2014
Location: NJ
Posts: 12
|
Thanks!!!!! I'll check it out.
|
|
|
05-11-2014, 05:58 PM
|
#5
|
Senior Member
Join Date: May 2010
Location: Rochester, NY
Posts: 1,605
|
Quote:
Originally Posted by gotokeys
Thanks!!!!! I'll check it out.
|
photos are on page 2 of this post I made when I had the problem http://www.keystonerv.org/forums/showthread.php?t=10801
|
|
|
05-12-2014, 04:56 AM
|
#6
|
Senior Member
Join Date: Apr 2014
Location: Berkley
Posts: 751
|
You might check the connector at the top of the arm where the power is supplied to the motor. This weekend while washing and waxing mine I happened to notice that the small two way black connector, wasn't connected 100%. Never lost power to the awning but it wasn't plugged in all the way. I believe this connector is there so you can run some jumper wires up to it and give the motor power to retract it in case of a problem elsewhere.
__________________
2022 Ford F150 3.5 Ecoboost SCrew 4x4 MaxTow
2020 Salem Hemisphere Hyper-Lyte 25RBHL
|
|
|
05-12-2014, 01:50 PM
|
#7
|
Junior Member
Join Date: May 2014
Location: NJ
Posts: 12
|
Thanks for the picture but thats not what I have. I found the splice it was in the wall behind the vertical rail of the awning. Keystone said that they dont splice them there!! Yeah right.
|
|
|
05-12-2014, 01:51 PM
|
#8
|
Junior Member
Join Date: May 2014
Location: NJ
Posts: 12
|
I'll have to figure out how to post pictures.
|
|
|
05-12-2014, 03:55 PM
|
#9
|
Senior Member
Join Date: Apr 2014
Location: Berkley
Posts: 751
|
Quote:
Originally Posted by gotokeys
Thanks for the picture but thats not what I have. I found the splice it was in the wall behind the vertical rail of the awning. Keystone said that they dont splice them there!! Yeah right.
|
If you found this, it should be fairly easy. Unplug the splice and hookup a voltmeter across it. Push the button. If you have voltage, then the wiring from there going into the motor is broken or the motor is broken. If not, then it may be the switch or something in behind your control panel that is connected to the switch.
__________________
2022 Ford F150 3.5 Ecoboost SCrew 4x4 MaxTow
2020 Salem Hemisphere Hyper-Lyte 25RBHL
|
|
|
05-13-2014, 03:25 PM
|
#10
|
Junior Member
Join Date: May 2014
Location: NJ
Posts: 12
|
Thanks for all the help awning is fixed!!
|
|
|
05-14-2014, 04:41 AM
|
#11
|
Senior Member
Join Date: Apr 2014
Location: Berkley
Posts: 751
|
Quote:
Originally Posted by gotokeys
Thanks for all the help awning is fixed!!
|
What ended up being the solution?
__________________
2022 Ford F150 3.5 Ecoboost SCrew 4x4 MaxTow
2020 Salem Hemisphere Hyper-Lyte 25RBHL
|
|
|
05-18-2014, 10:10 AM
|
#12
|
Junior Member
Join Date: May 2014
Location: NJ
Posts: 12
|
Bad splice. Found it behind a big blob of silicon in the sidewall behind the vertical awning rail. Keystone told me they don't splice in the wall!
|
|
|
05-19-2014, 04:25 AM
|
#13
|
Senior Member
Join Date: Apr 2014
Location: Berkley
Posts: 751
|
Quote:
Originally Posted by gotokeys
Bad splice. Found it behind a big blob of silicon in the sidewall behind the vertical awning rail. Keystone told me they don't splice in the wall!
|
Probably not normal, but that doesn't mean it doesn't happen. I'm sure the guys that build it have prints to follow, but lets say its a friday afternoon at 3:45 pm and they leave at 4...
So far the only noticeable thing I have seen is a bolt missing from the bracket that holds the power awning. Going to have to get that looked at soon I think. Nice blob of silicon there, I assume they squirt it in prior to installing the bolt....yet no bolt.
__________________
2022 Ford F150 3.5 Ecoboost SCrew 4x4 MaxTow
2020 Salem Hemisphere Hyper-Lyte 25RBHL
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|