|
10-21-2012, 06:21 AM
|
#1
|
Member
Join Date: Apr 2012
Location: Newark,Ca
Posts: 91
|
Pullrite Lubricant
What lubricant are you all using on your Pullrite Super Glides? Also do some need to be greased? Mine had alot of grease on it when I purchased it. I steam cleaned it all off. Now its nice and clean. I wont be able to get the Pullrite specific spray at the moment. So was looking for an alternative till I can order some.
__________________
2015 GMC 2500 HD
2012 314FWRLS Copper Canyon
Pullrite Superglide 16K Hitch
[B]Honda 3000IS
|
|
|
10-21-2012, 08:57 AM
|
#2
|
Member
Join Date: May 2012
Location: Kingston WA
Posts: 93
|
The owner's manual that came with our PullRite specifies spraying WD-40 on the tops and inside vertical surfaces of the square tubes that the sliding mechanism travels on, so that's what I use.
Happy trails,
__________________
Bill Stuart
2012 Alpine 3555RL
2015 RAM 3500 Laramie Limited Mega Cab Dually 4X4 Cummins, Aisin trans, 4.10 gears
Andersen Ultimate 5th Wheel Connection
Previous RV's:
1992 Prowler 35' Bunkhouse
1986 Fireball 30'
1978 Nomad 24'
1963 Kenskill 19.5'
1972 Dyna Cruiser Camper on '72 F-250
A Tent
|
|
|
10-21-2012, 02:52 PM
|
#3
|
Member
Join Date: Jun 2011
Location: Texas
Posts: 89
|
It depends on what you are greasing... Capture plate surface? Rails? My rails require a good axle grease.
I am assuming you bought a used one? Find out the manufacture date and model. Call Pullrite and ask them to make sure when you do. Their customer service is solid, even if you are not the original owner.
__________________
CampJKL
2007 Dodge CTD MegaCab Laramie 4x4 Dually
2012 Cougar 324 RLB
|
|
|
10-21-2012, 03:27 PM
|
#4
|
Senior Member
Join Date: Dec 2011
Location: Tazewell, Virginia
Posts: 286
|
WD 40 is what i use on my super glide hitch.
__________________
HAPPY TRAILS TO YOU
Jim, Kay, & Our Furry Kids
2012 Cougar HC 5er 291RLS aka "Rt 66 B&B"
2008 Toyota Tundra aka "The Hoss" 4X4 Limited DC 5.7 L
6 S Tranny w/TowHaul 4.30 RG 20" tires
Firestone Airbags w/compressor
16K Superglide hitch
Lovers of Route 66
|
|
|
10-21-2012, 04:59 PM
|
#5
|
Junior Member
Join Date: Mar 2011
Location: Illinois
Posts: 17
|
Quote:
Originally Posted by 35mastr
What lubricant are you all using on your Pullrite Super Glides? Also do some need to be greased? Mine had alot of grease on it when I purchased it. I steam cleaned it all off. Now its nice and clean. I wont be able to get the Pullrite specific spray at the moment. So was looking for an alternative till I can order some.
|
I've been using WD-40 as directed for a couple of years now with no issues. Spray a light coat on as directed each time before I hitch up. Every six months or so take it out of the truck and clean it up good, then re-lube with the WD-40.
Still working like a charm and I love it! Best hitch I've ever owned.
|
|
|
10-21-2012, 07:02 PM
|
#6
|
Senior Member
Join Date: Dec 2011
Location: Whittier, Ca
Posts: 181
|
Quote:
Originally Posted by billstuart
The owner's manual that came with our PullRite specifies spraying WD-40 on the tops and inside vertical surfaces of the square tubes that the sliding mechanism travels on, so that's what I use.
Happy trails,
|
X2
Jerry
__________________
Jerry
2008 Keystone Springdale 242FWRLSSR 5th wheel
2011 Chevy 2500 6.0 gas
16K Super Glide Sliding Hitch
|
|
|
10-22-2012, 12:59 AM
|
#7
|
Senior Member
Join Date: May 2010
Location: Plymouth,Ia
Posts: 109
|
On the newer ones with the plastic slide inserts you use WD-40. On the older units before using the inserts you use a dry graphite spray. I don't think they recommend grease anymore, it collects dirt and acts like sandpaper. Check on Pullrites website for a operators manual.
__________________
2010 2500HD LTZ Duramax
2010 Cougar 327RES
|
|
|
10-22-2012, 12:37 PM
|
#8
|
Member
Join Date: Apr 2012
Location: Newark,Ca
Posts: 91
|
Mine does not have a model number or manufacture date. Just weight ratings and instructions on how to use it on the sticker.
|
|
|
10-22-2012, 02:00 PM
|
#9
|
Senior Member
Join Date: Jan 2010
Location: Fulltiming
Posts: 423
|
Grease
Mine said to use silicon spray grease.
__________________
Jim, Sharon & Riley
2018 Keystone Alpine 3500Rl
2016 Ford F-350 Dually
Curt Q24 hitch for in bed puck system
Fulltimng.
|
|
|
10-22-2012, 02:21 PM
|
#10
|
Member
Join Date: Apr 2012
Location: Newark,Ca
Posts: 91
|
Just got off the phone with Pullrite. Mine is the model before they went to Teflon. He said to use medium duty grease. That is going to be messy.
|
|
|
10-22-2012, 09:19 PM
|
#11
|
Member
Join Date: May 2011
Location: Bakersfield, CA
Posts: 68
|
I spray Slip Plate on my rails as recommended by Pullrite and enjoy the fact it does not collect dirt and dust. Seems there several recommendations based on the model/year hitch you have. Slip Plate is widely available at local stores and online.
I bought my 16K hitch in August 2010 but had I waited another year, the hitch would likely have the nylon/teflon slide surfaces.
__________________
Rick & Carol
_____________________________
2011 Ford F250 6.7L SB Super Duty
Firestone Ride-Rite Air Bags
2011 Jayco Pinnacle
16k Pullrite SuperGlide w/SuperRails
2011 Polaris Ranger XP 800
|
|
|
10-29-2012, 03:03 AM
|
#12
|
Member
Join Date: Jun 2011
Location: Texas
Posts: 89
|
Hey I recognize that hitch now... You got a deal in it...something like $450! Awesome find.
Again I the 18k version... Grease it is...and thats why you had all the grease on at purchase...it looks almost like new since your first posts!
__________________
CampJKL
2007 Dodge CTD MegaCab Laramie 4x4 Dually
2012 Cougar 324 RLB
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|