Added Water Shut-off Valves

[Maxzd]

Typical RV has 3 drains for water. Fresh water drain from the fresh water tank, and two low point drains for hot and cold lines.

On occasion it's required to open these, usually during winterization, but sometimes just to flush sediment or stale water. If your setup is like mine, you have a cap on each drain. Works fine if you want to completely drain, but next to impossible to put the cap on once water is flowing.

The answer is shut off valves. I cut the 1/2" pex pipe leaving generous amounts on each side.

http://www.sabyland.com/wp-content/uploads/2012/01/20120107-151047.jpg

Next I took the original ends into the house and crimped the valve.

http://www.sabyland.com/wp-content/uploads/2012/01/20120107-151201.jpg

After that was done back out to the 5th wheel to crimp them onto the pex lines coming out of the unit. Took me a little bit to align the shut off valves and get the crimper to fit but mission accomplished.

Result is shut off valves and still the original caps if they accidentally opened, leaked or someone was messing around won't lose water.

http://www.sabyland.com/wp-content/uploads/2012/01/20120107-151445.jpg

I bought a similiar shut off valve for the fresh water tank. Unfortunately it won't work as the fresh water tank uses a 1/2" hose for the drain not pex. Didn't look before I left to go buy the fittings, I should have known it was hose not pex. Rather than hose clamp the pex valve and take a chance it leaks, I will get a hose-to-pex fitting or different shut off 1/2" hose valve for the fresh water tank. (potentially the fitting below, and add pex pipe and use the pex valve I bought). The shut off valve is cut a bit short on my unit, tough to get access to behind sewer pipe. I want to extend it anyway and I'll still have plenty of ground clearance, the spare tire sits way lower.

http://www.sabyland.com/wp-content/uploads/2012/01/images.jpg

Total Install Time : 25 Minutes
Total Project Cost : $30.60 for 3 1/2" Pex Shut off Valves, 10 pack of 1/2" Pex Crimp Rings. Had the tools already, Pex Crimpers start at 50 bucks.

[JRTJH]

PEX Crimping tools are pretty expensive. There are a couple of alternatives. You could rent one from True Value Hardware for about $5 a day or you could go on Ebay and bid on one. There are several "buy it now" with free shiping for about $30 or there are a couple of auctions that have a day or two left and are less than $10. When I bought mine from Ebay last year, I got it in an auction with free shipping for $6.00. So if you want to accomplish this very handy looking mod, don't think you'll have to buy the tool for $50+ and only use it once. There are alternatives :)

Nice mod Maxzd, thanks for sharing :)

[SteveC7010]

Another way to add shut-offs to the drains is to locate a supplier of the "Flair-It" fittings that are used throughout the trailers these days.

They have a 1/2" Straight Stop that would do the job:
http://mobilehomepartsstore.com/Merchant2/graphics/00000001/160601zm.jpg

In this particular case, the stop would slide on the tubing in place of the existing end cap fittings. The end cap itself should screw right on to the other side of the Straight Stop from the tubing.

I found this supplier after quite a bit of Googling. Once I figured out what the trade name for the fittings was, the search got a lot easier. I am not recommending this particular supplier, but they do have a good selection of the Flair-It fittings. I am certain that there are many other suppliers.

http://mobilehomepartsstore.com/Merchant2/merchant.mvc?Screen=PROD&Product_Code=160601

[chuck&gail]

THANKS! Just ordered two of those valves, appreciate the link. I'm handicapped and getting those caps off is really hard for me. Now I'll just throw the caps away!

[SteveC7010]

THANKS! Just ordered two of those valves, appreciate the link. I'm handicapped and getting those caps off is really hard for me. Now I'll just throw the caps away!

Chuck,

I don't know if you noticed, but over on the right hand column of the page I referenced, they offer a little hand tool for tightening and loosening the Flair-It fittings. It might be a good thing for you to have on hand when you replace the end caps, and perhaps for repairs or mods in the future.

[hankaye]

Howdy All;

Kinda like these;

http://www.sharkbiteplumbing.com/fittings

hankaye

[CarKath]

If I was doing same mod, I'd be using sharkbite fittings. Extremely user friendly. I have used for other tasks, love'm. Cost effective as well.

No cripping tools or any tools for that matter. Unless you buy a tool to take apart. Mine cost me $2.50

JMHO
Carl

[LeftyS7]

I bought a similar shut off valve for the fresh water tank. Unfortunately it won't work as the fresh water tank uses a 1/2" hose for the drain not pex. Didn't look before I left to go buy the fittings, /images.jpg[/IMG]


Why can't you use PEX fitting with any same size ID Hose? Can't you just clamp the hose and PEX with a screw type hose clamp? What is the difference between 1/2" ID PEX hose and other 1/2" hose?

[hankpage]

1/2" Pex is the same size OD as 1/2' Copper and takes the same size "Shark-bite" fittings .... as mentioned before this is an easy and quick way to go. I keep assorted shapes and sizes in my tool box for on the road repairs. I put 1/2" PEX "(technically 5/8 OD nom copper) x 3/8" comp. straight stops (like what's on your toilet in your stick house) for low point drains. Fresh water drain is not Pex so a barbed fitting is needed. JM2¢, Hank

[SteveC7010]

Why can't you use PEX fitting with any same size ID Hose? Can't you just clamp the hose and PEX with a screw type hose clamp? What is the difference between 1/2" ID PEX hose and other 1/2" hose?

The barbs on 1/2" PEX fittings and the barbs on fittings designed for 1/2" hose are differently sized and shaped. Remember that the PEX barbs are clamped with the special PEX fitting. Worm clamps are best used on fittings with the right barbs and the softer hose material.

It's as much about the right part for the job as it is about the right tool for the job. I'm not opposed to McGyvering things when necessary, but if you're in the plumbing aisle at Home Depot already, it just makes good sense to purchase the proper part for the job. On the subject of cost, the last I looked, PEX fittings were more expensive than standard ones. If that is still the case, that would reinforce my thinking on the matter even more.

[cabinfever]

Sharkbite and Pex are great! After using Pex one time with my brother in law plumber, I bought the crimp set. I think I paid $75 for it but well worth it. Pex saves so much time. Sharkbite follows closely behind the Pex. The only drawback are some of the Sharkbite items are a bit pricey compared to Pex. Both will make a plumber out of just about anyone.

[Bob Landry]

Another way to add shut-offs to the drains is to locate a supplier of the "Flair-It" fittings that are used throughout the trailers these days.

They have a 1/2" Straight Stop that would do the job:
http://mobilehomepartsstore.com/Merchant2/graphics/00000001/160601zm.jpg

In this particular case, the stop would slide on the tubing in place of the existing end cap fittings. The end cap itself should screw right on to the other side of the Straight Stop from the tubing.

I found this supplier after quite a bit of Googling. Once I figured out what the trade name for the fittings was, the search got a lot easier. I am not recommending this particular supplier, but they do have a good selection of the Flair-It fittings. I am certain that there are many other suppliers.

http://mobilehomepartsstore.com/Merchant2/merchant.mvc?Screen=PROD&Product_Code=160601

That's what I used. I simply replaced the screw on caps with these. Just about any RV dealership parts department should carry the Flair-it line. They are commonly used fittings and no big secret. I didn't see a need to even keep the caps since using them would be rather redundant.

[Javi]

That's what I used. I simply replaced the screw on caps with these. Just about any RV dealership parts department should carry the Flair-it line. They are commonly used fittings and no big secret. I didn't see a need to even keep the caps since using them would be rather redundant.
I've been slowly cutting these into my water lines as I get the time... Next is the outdoor shower.... never use it so it will be cut off so I don't have to worry with draining it every time we go out during the winter.. Already done the toilet, shower, and sink in the bath...

[Stublejumper]

Nice mod ,I think I will pick up the supplies tomorrow and complete this,thanks