|
10-05-2017, 03:58 PM
|
#1
|
Junior Member
Join Date: Jul 2017
Location: Yakima
Posts: 8
|
Height of the pin box
We have a 30 foot Springdale. We originally had a GMC Sierra 1500 but have discovered that is not as powerful as we would like. We sold the truck and got a Ram Laramie 2500. Bed of the truck/hitch is much taller than our GMC Sierra. We want to adjust the pin box and move the hitch up higher. We need to do this to level out the ride of the trailer otherwise the back bumper is too low when we are towing. Any new mind give us advice?
Sent from my iPhone using Tapatalk
|
|
|
10-05-2017, 05:30 PM
|
#2
|
Senior Member
Join Date: Sep 2011
Location: Northville NY in the Adirondacks
Posts: 2,128
|
Quote:
Originally Posted by chapmana.0216
[IMG]We have a 30 foot Springdale. We originally had a GMC Sierra 1500 but have discovered that is not as powerful as we would like. We sold the truck and got a Ram Laramie 2500. Bed of the truck/hitch is much taller than our GMC Sierra. We want to adjust the pin box and move the hitch up higher. We need to do this to level out the ride of the trailer otherwise the back bumper is too low when we are towing. Any new mind give us advice?
|
It may be easier to adjust the height of your fifth wheel in the truck bed *IF* it can be done and maintain adequate clearance between the trailer and the bed rails of the pickup box. Even adjusting the pin box will have the same issue.
I would caution you that no matter which you end up adjusting (pin box or fifth wheel), there are torque specs for re-tightening all the bolts on either or both. The manufacturer of your fifth wheel hitch will have the information on their website, most likely in the downloadable installation instructions for your model. If you have a stock pin box, it's most likely a Lippert and they should have the specs on their website.
__________________
'11 Cougar 326MKS loaded with mods
'12 Ford F250 SuperCab 6.7 PowerStroke Diesel
Amateur Radio: KD2IAT (146.520) GMRS: WQPG808 (462.675 TPL 141.3)
|
|
|
10-05-2017, 06:01 PM
|
#3
|
Site Team
Join Date: Jul 2014
Location: Modesto
Posts: 20,325
|
Only additional information I would add is if you do move the pin box, make sure to use the same number of bolts on each side. Put an upward load on the pin box BEFORE you tighten the bolts. We use an impact gun turned up all the way (140 PSI) and I’m willing to bet we get upwards of 200 lb/ft of torque on them.
Reason for upward pressure is there is some play in the holes, and when hitched up there is upward force exerted, so take it out before you tighten things up. We use the forklift at work. When I changed my pin box at home, I set it on the hitch and retracted the front jacks just enough to take all the play out.
__________________
2012 Copper Canyon 273FWRET being towed by a 1994 Ford F350 CC,LB,Dually diesel.
Airlift 5000 bags, Prodigy brake control, 5 gauges on the pillar.Used to tow a '97 Jayco 323RKS.
Now an RVIA registered tech. Retired from Law enforcement in 2008 after 25+ yrs.
|
|
|
10-05-2017, 08:23 PM
|
#4
|
Senior Member
Join Date: Apr 2012
Location: Portland, OR
Posts: 4,218
|
Quote:
Originally Posted by chuckster57
Only additional information I would add is if you do move the pin box, make sure to use the same number of bolts on each side. Put an upward load on the pin box BEFORE you tighten the bolts. We use an impact gun turned up all the way (140 PSI) and I’m willing to bet we get upwards of 200 lb/ft of torque on them.
Reason for upward pressure is there is some play in the holes, and when hitched up there is upward force exerted, so take it out before you tighten things up. We use the forklift at work. When I changed my pin box at home, I set it on the hitch and retracted the front jacks just enough to take all the play out.
|
I would look up the manufacturer torque spec for the pin box bolts and use a torque wrench to tighten to the correct specifications, over torquing a bolt can lead to the bolt failing!
__________________
Russ & Paula and Belle the Beagle.
2016 Ram Laramie 3500 DRW 14,000# GVWR (New TV)
2005 Copper Canyon 293 FWSLS 32’ GVWR 12,360
Visit and enjoy Oregon State Parks
|
|
|
10-05-2017, 08:35 PM
|
#5
|
Member
Join Date: Sep 2017
Location: MOODY
Posts: 72
|
had a similar issue with the cedar creek rig I had. (trading in tomorrow).dodge ram crew cab 4 X4. to clear bed rails had to have axles raised to get clearance on bed. had done at a truck/trailer alignment shop in tx.
Finally replaced bed with a C&M flat bed with a dove tailed end works great
__________________
Texas-traveler
Moody, Texas
|
|
|
10-06-2017, 04:51 AM
|
#6
|
Site Team
Join Date: Jul 2014
Location: Modesto
Posts: 20,325
|
Height of the pin box
Quote:
Originally Posted by rhagfo
I would look up the manufacturer torque spec for the pin box bolts and use a torque wrench to tighten to the correct specifications, over torquing a bolt can lead to the bolt failing!
|
I agree, but According to Lipperts web site torque values for standard pin box are not published. If you look at either aftermarket they say 3/4" bolts need a minimum of 210 lb/ft. Common 1/2" drive torque wrench limit out at well under that.
I do happen to have a 3/4" drive torque wrench at home for my auto business and it limits out at 300, so that's why we use an impact gun at the dealership.
__________________
2012 Copper Canyon 273FWRET being towed by a 1994 Ford F350 CC,LB,Dually diesel.
Airlift 5000 bags, Prodigy brake control, 5 gauges on the pillar.Used to tow a '97 Jayco 323RKS.
Now an RVIA registered tech. Retired from Law enforcement in 2008 after 25+ yrs.
|
|
|
10-08-2017, 05:02 PM
|
#7
|
Senior Member
Join Date: Jun 2015
Location: Montana
Posts: 102
|
Quote:
Originally Posted by texas-traveler
had a similar issue with the cedar creek rig I had. (trading in tomorrow).dodge ram crew cab 4 X4. to clear bed rails had to have axles raised to get clearance on bed. had done at a truck/trailer alignment shop in tx.
Finally replaced bed with a C&M flat bed with a dove tailed end works great
|
What's the average cost now days to have the axles flipped on a 5th?
__________________
2006 Doge Ram w/5.9 diesel - 2007 37' Copper Canyon w/5000 watt Honda Genset and Direct TV Kings Quest portable.
|
|
|
10-08-2017, 05:17 PM
|
#8
|
Member
Join Date: Sep 2017
Location: MOODY
Posts: 72
|
If I remember it was less than $200 to get mine raised. My old unit had multi hole shackles they only had to remove the shackle bolts and go to the next hole.
__________________
Texas-traveler
Moody, Texas
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|