|
03-12-2018, 05:54 PM
|
#1
|
Senior Member
Join Date: Jan 2012
Location: Coldwater, Mi
Posts: 386
|
Help Rotating Toilet
My toilet is turned a little too far and so it's easier to go by leaving the bathroom door open or sitting a little sideways on the throne. Otherwise, your knees are up against the bathroom door.
I want to rotate the toilet a few degrees counter-clockwise. So I removed the toilet and then removed all the screws from the flange. But it seems the pipe is glued into the actual tank, and I'm unable to budget it. Any thoughts on how I could break it free without breaking the black tank?
__________________
2014 Keystone Bullet Premier 22RBPR
2017 Chevy Colorado (Baby Duramax)
Propride P3 Hitch
|
|
|
03-12-2018, 05:58 PM
|
#2
|
Site Team
Join Date: Feb 2014
Location: W. Texas
Posts: 17,690
|
Had that dilemma (I think) years ago. I think you can take like a Dremel or similar tool with a round cutoff blade, cut around the inside of the sewer drain, remove it and replace with a new section that you can put the flange on...if that makes sense. You will need to reseal/glue the new section.
__________________
Danny and Susan, wife of 56 years
2019 Ram 3500 Laramie CC SWB SB 6.4 4x4 4.10
2020 Montana High Country 331RL
|
|
|
03-13-2018, 05:06 AM
|
#3
|
Senior Member
Join Date: May 2015
Location: Near Saratoga Springs,
Posts: 1,131
|
While I haven't had to remove that toilet flange on an RV did have to do it in the house. Using that Dremel or, better yet, a 1/4" chuck capacity die grinder, cut the top off then make one cut down the side of the fitting. By doing that, you may be able to break the rest free and slip the stub off easily with a screw driver as that cement will often break loose. Your replacement will need to be a black ABS or RV type fitting as you already have on your RV. It will need a dedicated ABS cement. A note on that cement - the combo PVC/ABS cement just isn't very good and may break loose due to driving vibrations.
Good luck and let us know how you make out with the project
|
|
|
03-13-2018, 06:41 AM
|
#4
|
Member
Join Date: Nov 2017
Location: Baton Rouge
Posts: 55
|
Quote:
Originally Posted by chartrand
My toilet is turned a little too far and so it's easier to go by leaving the bathroom door open or sitting a little sideways on the throne. Otherwise, your knees are up against the bathroom door.
I want to rotate the toilet a few degrees counter-clockwise. So I removed the toilet and then removed all the screws from the flange. But it seems the pipe is glued into the actual tank, and I'm unable to budget it. Any thoughts on how I could break it free without breaking the black tank?
|
I had to turn mine about 45 degrees.
Just took of the toilet and used a dremel to cut new holes on the flange for the two bolts that hold the toilet down. Used new gasket and it is working fine.
Obviously the people that build these things never use them.
__________________
Trailer 2016 Bullet Premier 19FBPR
Truck 2001 1500 Silverado
|
|
|
03-13-2018, 07:12 AM
|
#5
|
Senior Member
Join Date: Jan 2012
Location: Central San Joaguin Valley, CA
Posts: 2,117
|
Here you go NOTANLINES- another business opportunity - develop a swivel mount for the toilet and maybe add a rocker recliner option?
__________________
Jack & Marty
2018 Laredo 298 SRL
2011 F-250 SB Crew Cab 4x4 6.7L
|
|
|
03-13-2018, 07:31 AM
|
#6
|
Senior Member
Join Date: Jul 2011
Location: Fairhaven, MA
Posts: 354
|
I rotated my toilet a few degrees in a previous camper. I removed the toilet and the bolts to the floor. Then, I took a flat screw driver and hammer and gently tapped the flange and it began to rotate. When it was in the position I wanted, I put the bolts back in and reinstalled the toilet.
__________________
Greg
2022 Cougar 25RDS
2024 GMC Sierra 2500HD gas
Fairhaven, MA
|
|
|
03-13-2018, 07:59 AM
|
#7
|
Site Team
Join Date: Feb 2014
Location: W. Texas
Posts: 17,690
|
Quote:
Originally Posted by jsmith948
Here you go NOTANLINES- another business opportunity - develop a swivel mount for the toilet and maybe add a rocker recliner option?
|
^^^^there you go!! I'm in....I think? Reckon you could work on a power recline option.....?
__________________
Danny and Susan, wife of 56 years
2019 Ram 3500 Laramie CC SWB SB 6.4 4x4 4.10
2020 Montana High Country 331RL
|
|
|
03-13-2018, 05:44 PM
|
#8
|
Senior Member
Join Date: Jan 2012
Location: Coldwater, Mi
Posts: 386
|
Quote:
Originally Posted by gregrc75
I rotated my toilet a few degrees in a previous camper. I removed the toilet and the bolts to the floor. Then, I took a flat screw driver and hammer and gently tapped the flange and it began to rotate. When it was in the position I wanted, I put the bolts back in and reinstalled the toilet.
|
I tried that, banged on it pretty hard, all to no avail, the glue is holding strong.
Sent from my iPad using Tapatalk Pro
__________________
2014 Keystone Bullet Premier 22RBPR
2017 Chevy Colorado (Baby Duramax)
Propride P3 Hitch
|
|
|
03-13-2018, 05:51 PM
|
#9
|
Senior Member
Join Date: Jan 2012
Location: Coldwater, Mi
Posts: 386
|
Quote:
Originally Posted by buvens
I had to turn mine about 45 degrees.
Just took of the toilet and used a dremel to cut new holes on the flange for the two bolts that hold the toilet down. Used new gasket and it is working fine.
Obviously the people that build these things never use them.
|
I think it’s time I invest in a dremel tool. I think I’ll try this before resorting to cutting off the flange.
Sent from my iPad using Tapatalk Pro
__________________
2014 Keystone Bullet Premier 22RBPR
2017 Chevy Colorado (Baby Duramax)
Propride P3 Hitch
|
|
|
03-13-2018, 06:07 PM
|
#10
|
Site Team
Join Date: Feb 2014
Location: W. Texas
Posts: 17,690
|
Quote:
Originally Posted by chartrand
I think it’s time I invest in a dremel tool. I think I’ll try this before resorting to cutting off the flange.
Sent from my iPad using Tapatalk Pro
|
WHAT!! No Dremel? You have to have one IMO. I've got 4 and almost bought another one here in FL for use in my daughter's house......get one....you NEED it!!
__________________
Danny and Susan, wife of 56 years
2019 Ram 3500 Laramie CC SWB SB 6.4 4x4 4.10
2020 Montana High Country 331RL
|
|
|
03-13-2018, 07:01 PM
|
#11
|
Site Team
Join Date: Mar 2011
Location: Gaylord
Posts: 26,996
|
Yup, a Dremel is a vital accessory for almost anyone. And, it'll pay for itself if you can hold your kids down and learn basic dental skills.... Needle nose pliers and a Dremel and you can do most anything the dentist does for a lot less money.....
__________________
John
2015 F250 6.7l 4x4
2014 Cougar X Lite 27RKS
|
|
|
03-14-2018, 03:30 AM
|
#12
|
Senior Member
Join Date: May 2015
Location: Near Saratoga Springs,
Posts: 1,131
|
Heck, even my DW has a rechargeable version Dremel to shorten our two pup toenails. I still prefer a 1/4" die grinder and have several, both air and electric powered though my 1/8" Dremel does get plenty of use
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|