|
03-14-2019, 06:37 PM
|
#1
|
Senior Member
Join Date: May 2018
Location: Oregon
Posts: 1,138
|
Fresh water tank crack repair
Quote:
Originally Posted by Bnftravel
Well after several days of searching and looking for repair tips for a cracked fresh water tank at the drain hole area I finally fixed it.
We have a 2017 keystone Bullet crossfire 2070bh.
Last season we noticed the fresh water holding tank was leaking.
First I was going to buy a new fresh water holding tank and decided to check into repairs and found that a electric plastic welder would work for this project.
My neighbor mentioned that he had one so I gave it a try and it worked out great.
It not only heated the plastic and sealed with the plastic rods it actually stiff and the bottom of the drain area and made it more solid and we no longer have a crack project took me approximately one hour to do.
I used a Mini-Weld Model 7 Airless Plastic Welder model #URE5700HT
If I didn’t have one I would’ve went out and purchased it for around $170 it is well worth every penny it will repair almost any plastic there is cracks holes whatever you need to fix this thing seems to do a great job I’m very pleased with it.
Some may say repairing freshwater holding tank’s won’t work but from what I’ve seen and what this little machine can do I beg to differ. I put about 15 to 18 gallons of water in it after the project was repaired and I have not had a drop of water leak out at all today so far so good will let everybody know down the road how I made out.
From what I read on purchasing a new tank was the issue with taking the old one out because of the straps being screwed in from the top side and the amount of time and effort it would’ve been would’ve needed to replace the tank this repair was a much better solution.
Happy campers in Bardstown Kentucky
|
That’s really cool! Congrats
|
|
|
03-16-2019, 07:00 AM
|
#2
|
Junior Member
Join Date: Nov 2018
Location: Bardstown
Posts: 19
|
Fresh water tank crack repair
Well after several days of searching and looking for repair tips for a cracked fresh water tank at the drain hole area I finally fixed it.
We have a 2017 keystone Bullet crossfire 2070bh.
Last season we noticed the fresh water holding tank was leaking.
First I was going to buy a new fresh water holding tank and decided to check into repairs and found that a electric plastic welder would work for this project.
My neighbor mentioned that he had one so I gave it a try and it worked out great.
It not only heated the plastic and sealed it with the plastic rods it actually stiffened the bottom of the drain area and made it more solid and we no longer have a crack. The project took me approximately one hour to do.
I used a Mini-Weld Model 7 Airless Plastic Welder model #URE5700HT
If I didn’t have one I would’ve went out and purchased it for around $170.00. It is well worth every penny and it will repair almost any plastic there is like cracks holes or whatever you need to fix that is plastic. This thing seems to do a great job and I’m very pleased with it.
Some may say repairing freshwater holding tank’s won’t work but from what I’ve seen and what this little machine can do I beg to differ. I put about 15 to 18 gallons of water in it after the crack was repaired and I have not had a drop of water leak out at all today. So far so good and will let everybody know down the road how I made out after a few trips.
From what I read on purchasing a new tank was the issue with taking the old one out because of the straps being screwed in from the top side and the amount of time and effort it would’ve been would’ve needed to replace the tank. This repair was a much better solution.
Happy campers in Kentucky
|
|
|
03-16-2019, 07:43 AM
|
#3
|
Senior Member
Join Date: Apr 2017
Location: Anchorage
Posts: 610
|
Quote:
Originally Posted by Bnftravel
Well after several days of searching and looking for repair tips for a cracked fresh water tank at the drain hole area I finally fixed it.
We have a 2017 keystone Bullet crossfire 2070bh.
Last season we noticed the fresh water holding tank was leaking.
First I was going to buy a new fresh water holding tank and decided to check into repairs and found that a electric plastic welder would work for this project.
My neighbor mentioned that he had one so I gave it a try and it worked out great.
It not only heated the plastic and sealed it with the plastic rods it actually stiffened the bottom of the drain area and made it more solid and we no longer have a crack. The project took me approximately one hour to do.
I used a Mini-Weld Model 7 Airless Plastic Welder model #URE5700HT
If I didn’t have one I would’ve went out and purchased it for around $170.00. It is well worth every penny and it will repair almost any plastic there is like cracks holes or whatever you need to fix that is plastic. This thing seems to do a great job and I’m very pleased with it.
Some may say repairing freshwater holding tank’s won’t work but from what I’ve seen and what this little machine can do I beg to differ. I put about 15 to 18 gallons of water in it after the crack was repaired and I have not had a drop of water leak out at all today. So far so good and will let everybody know down the road how I made out after a few trips.
From what I read on purchasing a new tank was the issue with taking the old one out because of the straps being screwed in from the top side and the amount of time and effort it would’ve been would’ve needed to replace the tank. This repair was a much better solution.
Happy campers in Bardstown Kentucky
|
Thanks for sharing how can you not be happy in a place like Bardstown.
My under belly is enclosed and I have a piece of pex running out with a cap on it. if your set up is like this is there enough pex to cut and put a new valve on? Pictures would be helpful.
__________________
Mike
2016 Ford F350 CC 6.7 4x4 SRW (Ghost Rider)
2017 Cougar 29 RKSWE (The Tumble Weed)
Connected by a Curt 15K WDH W/Sway Control
|
|
|
03-16-2019, 08:53 AM
|
#4
|
Junior Member
Join Date: Nov 2018
Location: Bardstown
Posts: 19
|
Pictures of repair
Here are a few pictures of the repair
|
|
|
03-16-2019, 11:42 AM
|
#5
|
Senior Member
Join Date: Apr 2017
Location: Anchorage
Posts: 610
|
Nice pictures are worth 1000 words when describing projects.
__________________
Mike
2016 Ford F350 CC 6.7 4x4 SRW (Ghost Rider)
2017 Cougar 29 RKSWE (The Tumble Weed)
Connected by a Curt 15K WDH W/Sway Control
|
|
|
03-16-2019, 12:07 PM
|
#6
|
Senior Member
Join Date: Jul 2013
Location: Liberty, Texas
Posts: 5,036
|
Very well done.
__________________
2018 Ram 3500 Laramie CC DRW LWB 4X4 Cummins Aisin 3.73
Reese Goosebox 20K
2018 Heartland Landmark 365 Oshkosh
2008 Bigfoot 25C9.4 LB Cabover
2023 CanAm Defender SXS
|
|
|
03-16-2019, 12:49 PM
|
#7
|
Senior Member
Join Date: Feb 2014
Location: radium hot springs bc
Posts: 2,007
|
Quote:
Originally Posted by Bnftravel
Hear are a few pictures of the repair
|
Nice repair. Did your fresh water tank not have a nipple with a cap for draining?
__________________
2018 Ram 3500 6.4 Harvest Edition
2018 Cougar 27RESWE
|
|
|
03-16-2019, 02:38 PM
|
#8
|
Junior Member
Join Date: Nov 2018
Location: Bardstown
Posts: 19
|
Quote:
Originally Posted by 66joej
Nice repair. Did your fresh water tank not have a nipple with a cap for draining?
|
Yes, I think we hit a higher bridge than the road over a creek or driving up to a road from a lower grass parking area and that is what I think cracked the tank outside the drain plug. The hard spout with the drain twist end was sticking down about 2 inches under the tank and it cought the road or bridge. I decided after the repair it would just be easier to put in a flat plug rather than a spout with en end cap. When we need to drain the tank I will just take the plug out.
ACTUALLY when do we really need to drain the tank? Just before Wintering. It’s only fresh water and can drain out on the ground.
|
|
|
03-16-2019, 03:30 PM
|
#9
|
Site Team
Join Date: Mar 2011
Location: Gaylord
Posts: 26,997
|
Our tank drains the same as yours, I installed a 90 degree elbow and a piece of half inch PEX with a 1/4 turn valve on the end. I routed it from the bottom of the tank to the back wall of the trailer where all I need to do to empty the FWT is reach behind the bumper and twist the valve. Easy mod and it's all tucked way up next to the trailer so it won't get damaged easily. I can't take any pictures now (can't get into the pole barn) but will in a couple weeks if needed.
__________________
John
2015 F250 6.7l 4x4
2014 Cougar X Lite 27RKS
|
|
|
03-16-2019, 03:37 PM
|
#10
|
Junior Member
Join Date: Nov 2018
Location: Bardstown
Posts: 19
|
Quote:
Originally Posted by JRTJH
Our tank drains the same as yours, I installed a 90 degree elbow and a piece of half inch PEX with a 1/4 turn valve on the end. I routed it from the bottom of the tank to the back wall of the trailer where all I need to do to empty the FWT is reach behind the bumper and twist the valve. Easy mod and it's all tucked way up next to the trailer so it won't get damaged easily. I can't take any pictures now (can't get into the pole barn) but will in a couple weeks if needed.
|
Sounds like a great idea. Next time I’m at Lowes I’ll see what they have and may do that as well.
Thanks
|
|
|
03-26-2019, 02:01 PM
|
#11
|
Senior Member
Join Date: Feb 2015
Location: Texas
Posts: 1,090
|
Quote:
Originally Posted by JRTJH
Our tank drains the same as yours, I installed a 90 degree elbow and a piece of half inch PEX with a 1/4 turn valve on the end. I routed it from the bottom of the tank to the back wall of the trailer where all I need to do to empty the FWT is reach behind the bumper and twist the valve. Easy mod and it's all tucked way up next to the trailer so it won't get damaged easily. I can't take any pictures now (can't get into the pole barn) but will in a couple weeks if needed.
|
Excellent idea.
We recently vaulted a ceiling in our house and when the existing ceiling was removed there was a 20 foot hot water line going across the space.
I went to HD and they were out of the 25 foot 1/2 inch PEX packages, so they sold me 100 feet for the same price... I have lots of PEX for projects now
The problem will be pulling the coroplast to get to the drain fitting... maybe I could just put the 90 on the existing line...
-Brian
__________________
2014 Bullet Premier 22RBPR - let the camping commence!
2013 F150 Platinum - 5.0 - 3.55 ELD + towing package
|
|
|
03-27-2019, 08:36 AM
|
#12
|
Senior Member
Join Date: Feb 2013
Location: Lacey, WA
Posts: 503
|
Quote:
Originally Posted by JRTJH
Our tank drains the same as yours, I installed a 90 degree elbow and a piece of half inch PEX with a 1/4 turn valve on the end. I routed it from the bottom of the tank to the back wall of the trailer where all I need to do to empty the FWT is reach behind the bumper and twist the valve. Easy mod and it's all tucked way up next to the trailer so it won't get damaged easily. I can't take any pictures now (can't get into the pole barn) but will in a couple weeks if needed.
|
Hi.... This is a Mod I would like to do. Is the 1/4 turn valve a positive lock type? If not.... Have you ever had any problems with the valve opening from vibrations while driving?
Thanks
Lee
|
|
|
03-27-2019, 10:45 AM
|
#13
|
Site Team
Join Date: Mar 2011
Location: Gaylord
Posts: 26,997
|
There are many different approaches to adding a drain valve to a fresh water tank. Here are some of them.
I used an available RV drain valve with a 3/8 or 1/2 inch barb. It's slow to drain the tank, for me a "good thing" because I don't want to wash away the gravel where I park my RV during the summer.
Here's a photo of the valve I used, available here: https://www.amazon.com/Camco-22223-D...20256663&psc=1 and some photos of what is currently under your trailer and ways to improve it.
__________________
John
2015 F250 6.7l 4x4
2014 Cougar X Lite 27RKS
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|