|
01-19-2010, 05:08 PM
|
#1
|
Guest
|
Stabilization on Keystone Passports
All you Keystone enthusiasts,
I mentioned stabilization in another thread, but this is general feeler for all Keystone Passport owners; What do you use to stabilize these lightweight trailers? Thanks, JW
|
|
|
01-21-2010, 11:27 AM
|
#2
|
Junior Member
Join Date: Nov 2009
Posts: 5
|
Well, we don't have a Passport, but we do have a 2010 Keystone Sprinter 318FLS. It's a double slide, 32' TT.
We stabilize with 4 wheel chocks, the electric units on each end, plus 2 screw top jack stands under the outboard ends of each slide rail. IT's been fine for us. I do have 4 more screw top jack stands that I can put under the frame rails, which if I did, I would put them evenly spaced as shown below.
The red X’s are the slide screw jacks
The blue bars are the factory electric stabilizers
The green X’s are the optional screw jacks (which we haven’t needed to use
|
|
|
01-22-2010, 05:17 AM
|
#3
|
Senior Member
Join Date: Mar 2009
Location: Alabama
Posts: 863
|
I just use the manual jacks that my Passport came with and chock the wheels, works fine for me.
__________________
2005 Springdale 249BH FW
2008 Toyota Tundra Crewmax 5.7L
Tow package
Timbrens
|
|
|
01-24-2010, 10:07 AM
|
#4
|
Guest
|
Stabilization on Keystone Passports
All, thanks for your replies. We have the Keystone power package that has the electric stabilizers.
4x4given, The diagram is nice. Our rig is smaller, I like the placement for the jacks.
Flyguy, I'm assuming you're using the new Linx Levelers orange chocks with the cutout for levelers. If you are, how many do you use?
We have been using the old yellow chocks left over from our popup. JW
|
|
|
01-24-2010, 11:34 AM
|
#5
|
Senior Member
Join Date: Mar 2009
Location: Alabama
Posts: 863
|
I use the cheap yellow chocks that Wal-Mart sells and my manual crank down scissor jacks at the corners.
__________________
2005 Springdale 249BH FW
2008 Toyota Tundra Crewmax 5.7L
Tow package
Timbrens
|
|
|
02-10-2010, 10:04 AM
|
#6
|
Guest
|
Stabilization on Keystone Passports
Another question along this thread,
Has anyone used the X chocks or BAL X chocks that CampingWorld or other vendors sell? Do they work as advertised? Thanks, JW
|
|
|
02-10-2010, 10:33 AM
|
#7
|
Senior Member
Join Date: Mar 2009
Location: Alabama
Posts: 863
|
Those X chocks work very well, however they will not work on the Passport series because of the "spread axle" design, the axles are too far apart for them to work as designed, maybe BAL will make one for that axle design.
__________________
2005 Springdale 249BH FW
2008 Toyota Tundra Crewmax 5.7L
Tow package
Timbrens
|
|
|
02-10-2010, 02:33 PM
|
#8
|
Guest
|
Stabilization on Keystone Passports
Thanks, Flyguy. JW
|
|
|
02-11-2010, 01:53 PM
|
#9
|
Senior Member
Join Date: Mar 2009
Location: Alabama
Posts: 863
|
There is something in the way of wheel chocks that you can do with the spread axle design, go to my homepage and open the folder on "Wheel Chocks" and there you will see a homebrew design that will work, just cut the spreaders to the appropriate length (for homepage access click on "Flyguy" in the upper left of this post and follow the menu choices).
__________________
2005 Springdale 249BH FW
2008 Toyota Tundra Crewmax 5.7L
Tow package
Timbrens
|
|
|
02-15-2010, 09:58 AM
|
#10
|
Junior Member
Join Date: Jan 2010
Posts: 6
|
This is what I used, just added 9" of threaded rod with a coupler nut and some jam nuts to the chock. I made the type with wood blocks and pipe clamp for my old tt but for the width of this design the wood would be very heavy.
I also changed my scissor jacks to 30" and added Ultra fabs stabilizers, trailer is rock solid. The axle is flipped to give better ground clearence and I hate carring lots of wood blocks so I went with the longer jacks, got them online for $90 tot. delivered.
__________________
08 F350 FX4 CC SB 6.4L
09 Keystone Passport 290BH
UF elec jack,30"scissor jacks+Eliminator Strut Stabilizer,PD9160+wizard,custom bumper hitch,added 18.5gal FW tank,Reese dualcam 800# WD,Fantastic Fan,Axle Flip,Lexan screen door covers.
My Mods.
|
|
|
02-15-2010, 10:05 AM
|
#11
|
Senior Member
Join Date: Mar 2009
Location: Alabama
Posts: 863
|
Nice use of pictures "goingnorth" and some good suggestions too!
__________________
2005 Springdale 249BH FW
2008 Toyota Tundra Crewmax 5.7L
Tow package
Timbrens
|
|
|
02-21-2010, 11:38 PM
|
#12
|
Junior Member
Join Date: Dec 2009
Location: Alamogordo, NM
Posts: 11
|
Power Package
We took delivery of our 2010 195RB Passport last spring, and love the power package that came with it. You have to love push button stabilizer and tongue jacks!!! We also use the lynx pads from Walmart with no problems. I have made a lot of modifications that I will get photos online soon.
We used our Passport all summer and a lot this winter as NM doesn't have very cold winters. Haven't had any problems with it at all. Hope you enjoy your new Passport.
__________________
U.S. Army Retired (SFC)
2008 Montana 3585
1999 Ford F350 Dually
Reese 16K Hitch
EU2000 Honda Generator
EU2000 Companion Honda Generator
|
|
|
02-22-2010, 06:46 AM
|
#13
|
Senior Member
Join Date: Mar 2009
Location: Alabama
Posts: 863
|
One of the most useful mods that I did was to install 12v outlets at the wheelwells (both sides), this allows me to use a 12v impact wrench and a 12v air pump to service my tires at roadside (I also have a 12v electric jack). I ran a length of wire loom from the battery box front to back under the trailer and encased #8 wire (black and white fused to 30a) in it as seen below:
Then using a hole punch I cut a hole to accept the outlet device, the following is a series of pictures showing the results:
I have been happy with the results.
__________________
2005 Springdale 249BH FW
2008 Toyota Tundra Crewmax 5.7L
Tow package
Timbrens
|
|
|
02-22-2010, 04:42 PM
|
#14
|
Guest
|
Ultra Fabs
Goingnorth,
How much did the Ultra Fabs run you? Did the dealer put them on? We are looking at the JT Strongarm stabilization system. We hear Ultra Fabs and JT are pretty good systems.
Also, I noticed that you have a 4" bumper hitch. How is that working out? I have the 4" square bumper that is welded on. I'm thinking of doing the same since I have two bikes to carry. The dealer told us that the bumper wasn't strong enough to support receiver-related equipment. Thanks, JW
|
|
|
02-27-2010, 06:10 PM
|
#15
|
Junior Member
Join Date: Feb 2010
Posts: 27
|
The Plug It Right Stabilizers are $279.95 including shipping. Same principal just another version.
|
|
|
02-28-2010, 03:40 PM
|
#16
|
Permanent User Ban
Join Date: Jan 2010
Location: Solomans Island Maryland
Posts: 37
|
X chocks
Quote:
Originally Posted by witekjm
Another question along this thread,
Has anyone used the X chocks or BAL X chocks that CampingWorld or other vendors sell? Do they work as advertised? Thanks, JW
|
If the BAL X chocks will work on your rig, they are the best product I have purchased for my TH it doesn't move at all.
Hope this helps
|
|
|
02-28-2010, 07:37 PM
|
#17
|
Senior Member
Join Date: Oct 2009
Location: Bessemer, Alabama
Posts: 323
|
Quote:
Originally Posted by soundman
If the BAL X chocks will work on your rig, they are the best product I have purchased for my TH it doesn't move at all.
Hope this helps
|
I don't believe they will work on the Passport line of TT's because they have the spread axle design. The axles are too far apart.
__________________
2013 F150 XLT Supercrew EcoBoost
'08 Passport 280BH
|
|
|
03-11-2010, 09:32 AM
|
#18
|
Junior Member
Join Date: Jan 2010
Posts: 6
|
Quote:
Originally Posted by witekjm
Goingnorth,
How much did the Ultra Fabs run you? Did the dealer put them on? We are looking at the JT Strongarm stabilization system. We hear Ultra Fabs and JT are pretty good systems.
Also, I noticed that you have a 4" bumper hitch. How is that working out? I have the 4" square bumper that is welded on. I'm thinking of doing the same since I have two bikes to carry. The dealer told us that the bumper wasn't strong enough to support receiver-related equipment. Thanks, JW
|
I paid $300 at camping world for mine, no one else had them at the time, then 6 weeks later they dropped the price to $250, not sure what it is now. I first installed them on my Jayco toyhauler for a year or so and then took them off when I sold it and put them on my passport allong with 30"scissor jacks. I have my tt in a barn so I can work on it year round.
I will turn on the heater and put in a movie for the kids and do whatever work I need doing.
I welded my own hitch up and it bolts to the bumper and the back of the frame, I also bolted 3' angle iron from frame to hitch to form a triangle. I don't have real good pics of what I did and I still have more to do back there.
In the fall when I hunt I take off the bike rack and put on a hitchhauler with an aluminum cargo box filled with scrap lumber and other stuff, weighs in at 300# bumper looks solid with someone jumping on it with it full. Time will tell.
Sorry I didn't respond sooner missed this thread the last couple times I visited.
I have some pics at my mods page, click my mods at bottom.
__________________
08 F350 FX4 CC SB 6.4L
09 Keystone Passport 290BH
UF elec jack,30"scissor jacks+Eliminator Strut Stabilizer,PD9160+wizard,custom bumper hitch,added 18.5gal FW tank,Reese dualcam 800# WD,Fantastic Fan,Axle Flip,Lexan screen door covers.
My Mods.
|
|
|
03-23-2010, 02:05 PM
|
#19
|
Guest
|
Stabilization on Keystone
Thanks for the reply. I'm going to try FlyGuy's chock block solution. I made a pair just yesterday and going to try them out next week. JW
|
|
|
04-14-2010, 08:48 PM
|
#20
|
Junior Member
Join Date: Apr 2010
Location: Idaho Falls, Idaho
Posts: 10
|
My last trailer was a passport 300bh, which was awesome by the way, but at the risk of sounding too simplistic here I just used plastic wheel chocks and the standard stabilizers that came on it. The aluminum structure on those things are very stiff and easy to get stable.
__________________
S.E. Idaho
Sprinter 301RMP
2007 Dodge- CUMMINS Powered
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|