Go Back   Keystone RV Forums > Keystone Fleet | Keystone RV Models > Fifth Wheels
Click Here to Login

Reply
 
Thread Tools Display Modes
 
Old 10-11-2018, 04:12 PM   #31
Tejastwister
Junior Member
 
Join Date: Jul 2018
Location: Richardson
Posts: 1
Added cutoff switch to my battery box. Also, added voltage indicator and
accessory port for solar.
Attached Thumbnails
Click image for larger version

Name:	Modified Battery Box With Cutoff Switch.jpg
Views:	23
Size:	175.0 KB
ID:	18901  
__________________

Tejastwister is offline   Reply With Quote
Old 10-11-2018, 08:52 PM   #32
JKS11
Junior Member
 
Join Date: Mar 2018
Location: Toms River
Posts: 7
Quote:
Originally Posted by ChuckS View Post
That’s gonna be a lot of current across that battery disconnect switch. The slides and LG draw the most current when operating. I’d leave them wired as is if it were me. Possible can of worms down the road if rewired
Aggreed! I am going to disconnect all electrical when i store it, ......JUST..... Disconnect the positive side of the battery.....no need for another swich. Take the wire off the battery post. Zip tie it off somewhare else. When you need it , screw it back on.
__________________

JKS11 is offline   Reply With Quote
Old 10-12-2018, 09:11 AM   #33
xrated
Senior Member
 
xrated's Avatar
 
Join Date: Oct 2016
Location: "Murvil, TN
Posts: 1,269
Using a switch or disconnect with a higher current rating than is needed will not cause any issues. Using fuses with a higher current rating than what they should be, may cause serious issues. And remember this, disconnect switches, like a battery isolation switch will have ratings for both voltage and current. If it is rated at let's say 50 amps at 12VDC, and you are using it at a higher voltage, the current rating will be less. Direct current (DC) will always have a tendency to "arc" when it is open if there is a load on it, so remember, when opening one, try to have the least amount of load on it as possible with the situation you are in...AND, operate the switch very quickly...in other words, don't lolly gag around when you are opening it, make it snap open. Just some random thoughts on the topic and things that you may already know, but it never hurts to remind...or enlighten!
__________________
2016 F350 King Ranch Crew Cab Dually Diesel 4x4
2017 Keystone Impact 303 T.H.
2014 Yamaha FZ09 (highly modded)
Excessive payload capacity is a wonderful thing

"If it ain't Fast....It ain't Fun"
xrated is online now   Reply With Quote
Old 10-12-2018, 01:40 PM   #34
tomd
Junior Member
 
Join Date: Oct 2017
Location: Oxnard
Posts: 22
battery switch vs disconnect

my opinion,
My Keystone Sprinter, like Just Beclause said, has a disconnect which does NOT disconnect the slide outs, leveler, or remote control items. I researched and decided that is good for me, I usually turn switch off but can still open slide and inspect now and then in storage.
The issue is of course, not everything is off, and I accidently left the patio light on (which remote turns on separate from the manual switch). Also, if you do any electrical work, disconnect is a must.

Safest isolation method is to disconnect the battery on the (-) negative terminal. Either remove cable or install a second switch. I recommend doing this for long storage periods (over month). Not much draw down in short time but you will need to charge up about every 6 weeks or so.
__________________
best regards,
Tom
tomd is offline   Reply With Quote
Old 10-12-2018, 02:19 PM   #35
Frederick
Member
 
Join Date: Aug 2014
Location: Sergeant Bluff IA
Posts: 32
I have a 2014 Alpine had to put full cutoff switch on positive cable
Frederick is offline   Reply With Quote
Old 10-13-2018, 02:32 PM   #36
apachewolf
Junior Member
 
Join Date: Aug 2015
Location: Tucson, AZ
Posts: 18
Cut-off switch

Since the wiring is only good for 30A there is no need for a 500A switch. And the slides don't draw 100A. But here is what you can do. The power switches are on the positive side of the battery lead the may still be circuits that are "hot". The best way to overcome that is to simple re-wire the switch the cut the power on the grounf or negative lead. That way once activated there is NO power flowing in any circuit, which is really what you want. And a 30A switch from a auto supply store will work fine.

Happy camping.
__________________

apachewolf is offline   Reply With Quote
Reply

Tags
battery

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Powered by vBadvanced CMPS v3.2.3
Disclaimer:

This website is not affiliated with or endorsed by the Keystone RV Company or any of its affiliates in any way. Keystone RV® is a registered trademark of the Keystone RV Company.


All times are GMT -8. The time now is 03:05 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2018, vBulletin Solutions, Inc.