|
|
10-28-2018, 09:22 AM
|
#21
|
Senior Member
Join Date: Oct 2012
Location: Guelph, On
Posts: 308
|
Correct me if I am wrong here please. I've been researching both hitches for when we pull the trigger and order our new 5th wheel. I've got an 18 2500 Ram with the Cummins. Ordered the truck with the factory 5th wheel prep pkg. Doing my reading it appears as though the Pullrite mounts and lines up directly over the ball mount whereas the Andersen has about a 6 inch offset moving the pin towards the rear of the truck therefore eliminating the need for a slider when used in a 6 foot box.
Asking for verification here please.
.
|
|
|
10-28-2018, 09:28 AM
|
#22
|
Member
Join Date: Sep 2018
Location: Burlington
Posts: 32
|
Keep in mind the further the actual Hitch Point is moved toward the Rear of the Truck, the more Weight it places on the Rear Axle. Think of it like your arm, hold your arm out and place some weight on it close to your elbow - then move it further and further out, it gets heavier and heavier. Having a 3/4 Tom Ram with a Cummins myself I bet Available Pin Weight is a LARGE concern and our most limiting factor regarding 5th Wheels.
|
|
|
10-28-2018, 09:51 AM
|
#23
|
Member
Join Date: Jun 2011
Location: pennsylvania
Posts: 41
|
I have the aluminum one , 39 lbs. no clanking or banging. buying a small pull behind thou, so I thought about selling it. excellent cond , not sure where you're at I'm in Pennsylvania,
|
|
|
10-28-2018, 09:57 AM
|
#24
|
Junior Member
Join Date: Oct 2018
Location: Sandy
Posts: 5
|
Anderson hitch is a breeze.
I have an aluminum Anderson hitch in my 1 ton GMC standard bed. I’m pulling a 36’ Montana (by Keystone).
You can pretty much carry the hitch to the bed with one hand if you wanted to.
It installs on just minutes. Just flip the ball to the up position, lay your hitch over the top of the ball, put in the cotter pin, tighten the three bolts to 40 PSI and you’re ready to haul your fifth wheel.
When you get to where you’re going (Aguanga Ca. And Yuma for us) just pull your Anderson hitch out by loosening the bolts, pull the cotter pin and lift out ( one handed if you’re showing off) flip the ball over and put back into the bed, lock it in place with the spring release catch that was installed at inititial installation above the left rear tire, put the rubber hole cover over the pin. You are now the guy that gets to haul all the golf clubs to the course.
|
|
|
10-28-2018, 10:03 AM
|
#25
|
Junior Member
Join Date: Oct 2018
Location: Sandy
Posts: 5
|
It helps but you still can’t turn 90 degrees. I found out the hard way. Although with that in mind I’m careful on tight back ins. And have no problems.
|
|
|
10-28-2018, 10:13 AM
|
#26
|
Junior Member
Join Date: Jun 2018
Location: Boaz
Posts: 13
|
Anderson versus gooseneck
I have the Anderson and enjoy pulling with it. However, I still consider it a hassle having to pull it out to hook up to a gooseneck cattle trailer. I am switching to the Reese Goosebox for my 5th wheel with a LIPPERT1116 pin box.
|
|
|
10-28-2018, 10:31 AM
|
#27
|
Member
Join Date: Sep 2018
Location: Burlington
Posts: 32
|
I have seen a “Gooseneck” adapter for RVs as well. It gets Bolted the 5th Wheel in place of the Stock Reciever - you hookup just like a Cattle/Farm Trailer. It also weighs FAR less than the Standard Hitch Assemblies that are being used. I’m actually surprised that Goodenecks aren’t more prevalent in 5th Wheel use. They have to be pretty strong considering the loads you see using them, all the while consisting of far less mass.
|
|
|
10-28-2018, 12:05 PM
|
#28
|
Junior Member
Join Date: Jun 2016
Location: Taos
Posts: 17
|
I love my Andersen! Lightweight easy to use no bucking no chucking just a solid connection.
Buuuuuutttttttt the Reese gooseball is a replacement pin box it doesn’t void warranties and all you have in the bed is the ball.
|
|
|
10-28-2018, 12:11 PM
|
#29
|
Site Team
Join Date: Jul 2014
Location: Modesto
Posts: 20,325
|
Quote:
Originally Posted by SteMax
I love my Andersen! Lightweight easy to use no bucking no chucking just a solid connection.
Buuuuuutttttttt the Reese gooseball is a replacement pin box it doesn’t void warranties and all you have in the bed is the ball.
|
And the Goosebox has an internal "air bag" that helps even more for a smooth ride. Just installed one Friday.
__________________
2012 Copper Canyon 273FWRET being towed by a 1994 Ford F350 CC,LB,Dually diesel.
Airlift 5000 bags, Prodigy brake control, 5 gauges on the pillar.Used to tow a '97 Jayco 323RKS.
Now an RVIA registered tech. Retired from Law enforcement in 2008 after 25+ yrs.
|
|
|
10-28-2018, 12:42 PM
|
#30
|
Member
Join Date: Sep 2018
Location: Burlington
Posts: 32
|
Reese Gooseball is the one I saw. The biggest Drawback I see is it may void any warranty on your Trailer (actually pretty likely), which to me is pretty important. I also don’t see the associated weight, but I assume it to be measurable, making it a pretty attractive option.
|
|
|
10-28-2018, 01:04 PM
|
#31
|
Site Team
Join Date: Jul 2014
Location: Modesto
Posts: 20,325
|
Reese goosebox does not void the lippert frame warranty.
__________________
2012 Copper Canyon 273FWRET being towed by a 1994 Ford F350 CC,LB,Dually diesel.
Airlift 5000 bags, Prodigy brake control, 5 gauges on the pillar.Used to tow a '97 Jayco 323RKS.
Now an RVIA registered tech. Retired from Law enforcement in 2008 after 25+ yrs.
|
|
|
10-28-2018, 02:13 PM
|
#32
|
Member
Join Date: Jan 2018
Location: Worthington
Posts: 50
|
Just a word of advice on this style of hitch. Make sure you carry the tools needed to remove the hardware from the pinbox. If your TV breaks down not to many good Samaritans will have the hitch to get you rig to a safe location.
|
|
|
10-28-2018, 03:05 PM
|
#33
|
Junior Member
Join Date: Feb 2015
Location: Mosinee, Wi
Posts: 18
|
Pullrite SuperGlide
I have the SuperGlide hitch and have been most disappointed with it. The hitch itself is solid and has performed admirably, however hooking up and disconnecting have been most challenging to the point where I am considering trading in my 5th wheel for a TT. You have about a 3/8 inch window to engage the hitch mechanism when connecting and you have to be aligned exactly with truck bed and hitch pin. Unhooking has its challenges as well. sometimes you have to "bump" the truck to get the hitch mechanism to release so you can disengage the handle.
Positive is I can turn almost 90 degrees with my short bed as the hitch mechanism moved up and down the rails.
While camping in New Mexico, a neighbor showed me his Pullrite that all you had to do was get the hitch pin at the bottom of a bowl like structure where it locked in place.
Good luck in your endeavor to find a hitch.
|
|
|
10-28-2018, 03:56 PM
|
#34
|
Member
Join Date: Aug 2015
Location: Downey, ca
Posts: 54
|
Quote:
Originally Posted by skdooman2004
I have the aluminum one , 39 lbs. no clanking or banging. buying a small pull behind thou, so I thought about selling it. excellent cond , not sure where you're at I'm in Pennsylvania
|
Thank you but I’m in Los Angeles, Ca.
|
|
|
10-28-2018, 05:57 PM
|
#35
|
Junior Member
Join Date: Sep 2018
Location: Neb City
Posts: 3
|
Love my Aluminum Anderson Hitch!
|
|
|
10-29-2018, 08:13 AM
|
#36
|
Junior Member
Join Date: Feb 2015
Location: Waterloo, NY
Posts: 5
|
Andersen
Had a B&W fifth wheel hitch, just too heavy to handle it by myself.
I have since changed to "The Andersen Ultimate" it's a pleasure to be able to remove and install effortlessly by my lonesome.
|
|
|
10-29-2018, 08:58 AM
|
#37
|
Senior Member
Join Date: Aug 2018
Location: Greenwood
Posts: 176
|
Have been using the Anderson hitch for 2 years now and love it. I have the aluminum model. Very easy to install and remove. Very easy to couple the trailer to also. Can’t speak for the other but as long as I have a fiver it’ll be an Anderson for me.
|
|
|
10-29-2018, 09:07 AM
|
#38
|
Member
Join Date: Jan 2018
Location: Worthington
Posts: 50
|
Quote:
Originally Posted by ancha71
I have the SuperGlide hitch and have been most disappointed with it. The hitch itself is solid and has performed admirably, however hooking up and disconnecting have been most challenging to the point where I am considering trading in my 5th wheel for a TT. You have about a 3/8 inch window to engage the hitch mechanism when connecting and you have to be aligned exactly with truck bed and hitch pin. Unhooking has its challenges as well. sometimes you have to "bump" the truck to get the hitch mechanism to release so you can disengage the handle.
Positive is I can turn almost 90 degrees with my short bed as the hitch mechanism moved up and down the rails.
While camping in New Mexico, a neighbor showed me his Pullrite that all you had to do was get the hitch pin at the bottom of a bowl like structure where it locked in place.
Good luck in your endeavor to find a hitch.
|
If I could offer you a tip for an easy hookup. Glue a paint stick or something similar to a magnet, place this on your ball and back up to the trailer. This makes it very easy to put your hitch pin exactly on center. When you get about a 45 degree tilt on your stick just lock it in with your emergency brake and you should have a perfect alignment for t h at easy hookup. This hack is a lot cheaper than changing out your hitch. Happy Camping
|
|
|
10-29-2018, 11:11 AM
|
#39
|
Junior Member
Join Date: Jul 2018
Location: Newcastle
Posts: 19
|
Anderson is a great hitch
I have the Anderson hitch and it has performed great. It is very easy to hookup. It has a funnel shaped receiver and you can be off more than two inches in any direction and still be able to get the ball inside the receiver. Then just push the cable in and it is locked in place. I was skeptical when I first got it but it has performed extremely well. I have the rail system in the bed and just pull out four pins and off it comes. It is also easy to put a long hasp lock on it for security. Someone mentioned about if you had a breakdown with TV. To convert bag to king pin just loosen 4 Allen head screws and remove 1bolt and you are back to 5er.
|
|
|
10-29-2018, 04:10 PM
|
#40
|
Junior Member
Join Date: Apr 2017
Location: Sayreville
Posts: 4
|
Quote:
Originally Posted by Kojak
Any thoughts on these two fifth wheel hitches? I currently own a Curtis 24K on a Ram 3500 factory pick system but its getting to be a pain in the *** when I want to remove it so I’m looking for something light weight. I can’t decide between the Anderson hitch or the Pullrite Superlite. Any thoughts?
|
I personally have a Demko 18K auto-slide hitch that I attach to under bed rails I installed in our Chevy 2500 HD but it is a heavy hitch that I can't remove without help...I too was thinking of the Anderson Hitch.. but here is a recent post on a RV Facebook post of an Anderson Hitch..not saying this is a bad hitch, or what caused the failure...but no matter what hitch you use...caution, common sense and safety all need to remain paramount.
|
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|