|
04-14-2014, 02:16 PM
|
#1
|
Junior Member
Join Date: Mar 2014
Location: Danville, VA
Posts: 15
|
Dump valve handle broke off...
Third trip out on my 2010 bullet and the dump handle broke off... Apparently, it is a two piece rod that is threaded together where it protrudes through the covered underbelly. I had about a quarter inch of remaining rod showing that I was able to pull with a pair of pliers to get it dumped but now I have to find a replacement rod and handle. I can't seem to find the same handle/rod anywhere online that I can just screw back up on there. I have been searching around and have found an extension that I'm sure I can rig on there to get it working again. The broken rod that I have is about 6" long with handle and the extension will make it 18". I'm wondering if it will be too close to the ground by adding an additional 12" of length to it. Has anyone ran into this problem before? I could probably get a sleeve to slip over the rods and join them together and hold them in place with set screws. Any advice?
Sent from my SM-N900V using Tapatalk
|
|
|
04-14-2014, 03:31 PM
|
#2
|
Site Team
Join Date: Mar 2009
Location: Fraser Valley BC Canada
Posts: 7,015
|
Camping World sells an aluminum handle and I believe you can also get the rod from them. I had a plastic handle that pulled out of the threads and used Loc-Tite to re-install it with the new metal one. Has held up since the repair ....touching wood. To take the stress off the handle, I now pull and push with one hand on the handle and one hand on the rod.
__________________
2008 Cougar 5th Wheel 27RKS
2005 2500 GMC Duramax
|
|
|
04-14-2014, 03:41 PM
|
#3
|
Gone Traveling
Join Date: Oct 2013
Posts: 48
|
If it's like the pulls on the trailers that have basement pulls they are put together with 1/4" all thread. I broke mine at the joint. I just got a length of 1/4" all thread and threaded it into the 2 sleeves. I measured what I needed first. The sleeves are threaded all the way through.
I hope I explained that so you can understand what I mean.
|
|
|
04-14-2014, 04:02 PM
|
#4
|
Junior Member
Join Date: Mar 2014
Location: Danville, VA
Posts: 15
|
Yeah. I may run to the hardware store and pick up some all thread, cut it to length and screw a handle on it. May be the cheaper route to go. I still have the male threaded end poking through the underbelly to attach to. Before ido that, I will check with camping world to see how much a replacement rod and handle will be. Thanks for the replies.
Sent from my SM-N900V using Tapatalk
|
|
|
04-14-2014, 04:05 PM
|
#5
|
Senior Member
Join Date: Apr 2011
Location: Arrey,
Posts: 2,368
|
acampbell1999, Howdy;
Here's a bit of help if you feel you want to stick to what came off...
http://valterra.com/product/waste-va.../?pcat_id=1709
hankaye
__________________
Striving for a less complicated life since 1949 ...
Home: 2008 Cougar 278 RKS
T.V.: 2004 F-250 4X4, Level III BulletProofed , Detroit Tru-Track Differential (915A550)
Dog: 2006 Border Collie (Rascal) aka Maximum fur dispersal unit. (08/04/2006 - 12/16/2017) RIP.
|
|
|
04-14-2014, 04:35 PM
|
#6
|
Junior Member
Join Date: Feb 2014
Location: Florida & North Carolina
Posts: 12
|
We had exactly the same thing happen on our 2013 Bullet the second time we dumped. I crawled underneath and dug out a wider hole in the underbelly so that we could get a grip on the stem with the pliers. We took it to CW in Midway. They didn't have the exact part, but they took what they had and improvised. It has worked well so far. We would like to get an extender though. lizzie
|
|
|
04-14-2014, 05:13 PM
|
#7
|
Junior Member
Join Date: Mar 2014
Location: Danville, VA
Posts: 15
|
Quote:
Originally Posted by hankaye
|
As much searching as I have done, I hadn't seen that. Thanks for the link. It would match the other one and look better.
Sent from my SM-N900V using Tapatalk
|
|
|
04-14-2014, 05:15 PM
|
#8
|
Junior Member
Join Date: Mar 2014
Location: Danville, VA
Posts: 15
|
Quote:
Originally Posted by lizzie
We had exactly the same thing happen on our 2013 Bullet the second time we dumped. I crawled underneath and dug out a wider hole in the underbelly so that we could get a grip on the stem with the pliers. We took it to CW in Midway. They didn't have the exact part, but they took what they had and improvised. It has worked well so far. We would like to get an extender though. lizzie
|
Maybe it's a bullet thing... I might be better off getting a spare for when the black water handle breaks.
Sent from my SM-N900V using Tapatalk
|
|
|
04-14-2014, 07:21 PM
|
#9
|
Member
Join Date: Sep 2013
Location: Farmingdale, NY
Posts: 35
|
Just make sure that the knife valve is working properly before you go through the trouble of finding a replacement handle. I had a similar issue happen to me on a previously owned TT years ago. Replaced the handle only to find out the entire valve was shot!
Valterra sells them and they are easy enough to install, $15 part. I believe CW website has a DIY Video on how to change out the entire valve. Not too much involved installing it. This way you will be able to replace the O-rings(gaskets) and you have a new valve. Good Luck.
__________________
2014 Bullet Premier 31 BHPR
2012 Ford F-350 Lariat CC Short Bed 6.7l Turbo Diesel
|
|
|
04-15-2014, 01:38 PM
|
#10
|
Senior Member
Join Date: Aug 2011
Location: Battle Creek
Posts: 163
|
You can use something like this until it's repaired.
http://www.amazon.com/Valterra-T58-T...W3J5DD5RK8V0AN
__________________
Bob & Sarah
2013 Bullet 248RKS (Taj Mahaul)
2013 Silverado 2500HD, 6L, 3.73 (Blizzard)
|
|
|
04-15-2014, 07:11 PM
|
#11
|
Member
Join Date: May 2013
Location: Fowlerville,MI
Posts: 78
|
I did what superdog404 did and it works great. A lot more sturdy than the cheap aluminum rods
|
|
|
05-26-2014, 07:26 PM
|
#12
|
Member
Join Date: Aug 2013
Location: Camarillo
Posts: 92
|
Quote:
Originally Posted by hankaye
|
we just lost ours over Memorial Day. is this threaded on both ends ( male and female), I can't tell?
__________________
2013 Cougar 28RBS
2013 Ram 1500 Hemi 3.92 axle
|
|
|
05-27-2014, 06:37 AM
|
#13
|
Senior Member
Join Date: Apr 2011
Location: Arrey,
Posts: 2,368
|
So Cal CPA, Howdy;
Quote:
Originally Posted by So Cal CPA
we just lost ours over Memorial Day. is this threaded on both ends ( male and female), I can't tell?
|
Yes. Internal (female), threads on one end and external (male), on the other.
hankaye
__________________
Striving for a less complicated life since 1949 ...
Home: 2008 Cougar 278 RKS
T.V.: 2004 F-250 4X4, Level III BulletProofed , Detroit Tru-Track Differential (915A550)
Dog: 2006 Border Collie (Rascal) aka Maximum fur dispersal unit. (08/04/2006 - 12/16/2017) RIP.
|
|
|
05-27-2014, 09:17 AM
|
#14
|
Member
Join Date: Aug 2013
Location: Camarillo
Posts: 92
|
Thanks, Ordering now.
__________________
2013 Cougar 28RBS
2013 Ram 1500 Hemi 3.92 axle
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|