|
06-06-2014, 03:53 AM
|
#1
|
Member
Join Date: Mar 2014
Location: Odenton, Maryland
Posts: 57
|
Outside Kitchen Shelf
So lesson learned for me and for anyone else in the future do not place anything heavy on the shelf in your outside kitchen. I placed two 12 packs of soda on the top shelf in our outdoor kitchen thinking they would be ok.... Needless to say I was wrong !!! when we got to the campground and we were setting up I open to the outside kitchen to find the shelf had been pulled down. It was only held up with staples (no surprise). So now I have to take out the bottom pull out shelf with the sink and stove to fix the shelf. Should be an easy job but I was a little disappointed to find that when we got to the camp ground. It only pulled down on the back side. Left and right were fine. I plan on adding some wood glue and a few screws. I though they would have made this shelf a little stronger.
__________________
2014 Bullet 308BHS
2013 Ram 1500 5.7Hemi, 8 Speed, 3.92 gears LSD, CC, 4x4
|
|
|
06-06-2014, 07:00 AM
|
#2
|
Senior Member
Join Date: Sep 2012
Location: Airdrie, Alberta
Posts: 552
|
Good to know; thanks for sharing. Sounds like many of us may be living on borrowed time...
i may add some quarter-round trim beneath the edges of the shelf to help support them.
I need to also find a spot to mount the bottle opener my DW bought me for Xmas, which won't rip the wall apart when used LOL
__________________
2013 Passport 3220BHWE, upgrade axles, Kumho Radial 857's, all LED, TST507 TPMS, Reese DCSC, DIY corner stabilizers
2012 Ram 1500 Sport crew cab, Hemi, 4x4, 3.92 LSD, factory brake controller, S&B CAI w/scoop, Moroso air/oil can, 87mm ported/polished/knife-edged throttle body, Magnaflow exhaust, 180* t-stat, Rear lowered 2", Airlift 1000.
|
|
|
06-06-2014, 09:38 AM
|
#3
|
Junior Member
Join Date: Mar 2014
Location: Edwardsville il
Posts: 15
|
I just got my new 2015 308BHS and when I got it home from the dealer the empty mini-fridge had put a hole in the shelf. It's the same material. They certainly did not think about what would happen if you put weight in it. I cut a piece of 1/2 inch plywood and just laid it across the other shelf to distribute the load. It's worked so far.
__________________
|
|
|
06-06-2014, 06:29 PM
|
#4
|
Member
Join Date: Nov 2013
Location: Upstate, NY
Posts: 91
|
Thanks for the heads up. I just noticed last weekend that the cast iron skillet I had in there was giving the shelf a little sag. Will pay closer attention to it now.
__________________
2013 Hideout 29BHS :2013-?
F250xlt, crew, 6.2, short bed, fx4
2009 Rvision Trailcruiser, TC26RKS: 2009-2012
|
|
|
06-07-2014, 04:15 PM
|
#5
|
Senior Member
Join Date: Feb 2013
Location: MA
Posts: 3,153
|
Sorry it happened but I am not surprised. The selves there are most likely made to hold spices, plastic bowls and the like, not heavier items.
__________________
2013 Premier 31BHPR
2014 F350 6.2L
Soon to be just DW and I
|
|
|
06-08-2014, 03:38 AM
|
#6
|
Senior Member
Join Date: Oct 2012
Location: Oakfield NY
Posts: 229
|
Sorry to here but i think u led me to my next mod slide out shelf for pans and spices
|
|
|
06-08-2014, 04:42 AM
|
#7
|
Senior Member
Join Date: Jan 2011
Location: Austin, Tx
Posts: 1,910
|
Plan on rebuilding drawer supports and slides also. Those was the first to go on my trailer, but I'm sure the cast iron didn't help either. Everything is put together with staples. To make it worse, if you look at how the staples are put in, you'l find a lot of places where they are put in with the grain instead of across, making them even easier to pull through the material.
__________________
2011 Outback 277RL
2013 F250 XLT Crew Cab 6.2L
Bitter Gun Owner
Bitter Clinger
Armed Infidel
|
|
|
06-09-2014, 03:33 AM
|
#8
|
Member
Join Date: Mar 2014
Location: Odenton, Maryland
Posts: 57
|
So I fixed my shelf this weekend !!! I pulled out the lower sliding shelf to gain access.... A lot of room once that was out. You just have to undo the water hoses. I pulled out all the staples and added wood screws for every spot there was a staple. That pulled the shelf up tight. I then added a piece of trimmed down scrap oak and placed it under the shelf for added support. I think I'm good now to place what ever on there. If the wood piece was a little thicker than the 1/8 piece in there I don't think it would have been an issue. The front and sides the shelf sits on top
@dougjoliefrey....yeah Mine did the same exact thing. It really helps to place the strap on it. Mine was like when we took delivery though. Well let me back that up and say the front trim piece of wood had a spot where the door hinge bolt had dug in a little. I just let it go, wasn't worth making that much of a fuss to me. I took the fridge out over the weekend and noticed in the back corner where it had cracked the floor almost a hole. I think I'm gonna add a piece of 1/4 plywood down too. I'm doing this b/c I've notice the door hits the lip of the camper opening (the rounded corner) when opening it if it isn't shifted all the way to the right. I've adjusted the front feet but I didn't want it tilting to far backwards.
__________________
2014 Bullet 308BHS
2013 Ram 1500 5.7Hemi, 8 Speed, 3.92 gears LSD, CC, 4x4
|
|
|
06-21-2014, 05:06 AM
|
#9
|
Member
Join Date: Feb 2012
Location: Lancaster, PA
Posts: 96
|
slide mod
I have the same set-up and have been thinking of doing somethign different -- can you please post photos of your mod to the outdoor kitchen??? Thanks!
__________________
Andrew Miller
Lancaster, PA
2011 Keystone Passport 3220BH Limited Edition
2010 Ford F-250 Diesel FX4, Crew Cab, 6.5 ft bed
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|