Forum: Repairs & Maintenance
01-13-2023, 11:36 PM
|
Replies: 5
Views: 2,737
|
Forum: Repairs & Maintenance
01-09-2023, 05:26 AM
|
Replies: 5
Views: 2,737
|
Forum: Modifications and Upgrades
12-23-2022, 02:36 AM
|
Replies: 21
Views: 8,293
Hi all. I'm in the "process" of shortening the...
Hi all. I'm in the "process" of shortening the length of the large slide and also overall length of our Cougar HC 299RKS. I've made some rollers to install when returning slide into it's normal...
|
Forum: Repairs & Maintenance
06-21-2022, 05:33 PM
|
Replies: 5
Views: 4,158
|
Forum: Fifth Wheels
04-23-2021, 05:50 PM
|
Replies: 24
Views: 3,923
|
Forum: Repairs & Maintenance
02-25-2021, 11:13 AM
|
Replies: 9
Views: 2,359
|
Forum: Repairs & Maintenance
09-08-2020, 04:16 AM
|
Replies: 7
Views: 2,757
|
Forum: Repairs & Maintenance
08-27-2020, 05:52 AM
|
Replies: 5
Views: 11,332
|
Forum: Fifth Wheels
08-03-2020, 02:01 PM
|
Replies: 50
Views: 31,563
|
Forum: Modifications and Upgrades
04-29-2020, 05:11 AM
|
Replies: 22
Views: 14,055
|
Forum: Repairs & Maintenance
04-25-2020, 01:21 AM
|
Replies: 3
Views: 1,428
Jacking up each end of the slide when it is...
Jacking up each end of the slide when it is against the wall does work (stays there), but a PITA to do each time. I should have said that the wear bar is in from the opening. Intend to install...
|
Forum: Repairs & Maintenance
04-22-2020, 01:05 PM
|
Replies: 3
Views: 1,428
Same happens on our 2011 Cougar HC 299 ctyrea -...
Same happens on our 2011 Cougar HC 299 ctyrea - cannot get the bottom in flush against the wall/seal. Makes sitting at the table on a slope uncomfortable.
Tried everything including Norco advice to...
|
Forum: Repairs & Maintenance
12-08-2019, 12:59 PM
|
Replies: 66
Views: 28,786
|
Forum: Repairs & Maintenance
12-07-2019, 11:49 PM
|
Replies: 66
Views: 28,786
Bought them pre cut from a local plastics...
Bought them pre cut from a local plastics supplier that supplies engineering & mining industry - used in high metal to metal wear areas. Installed 3" wide for each end, 2" for strip every 18" and 6"...
|
Forum: Repairs & Maintenance
12-06-2019, 12:47 PM
|
Replies: 66
Views: 28,786
Sonofcy The Darco looked like it was about to...
Sonofcy The Darco looked like it was about to tear in the centre of the large slide so after seeing another poster using UMHW I counter sunk / screwed UMHW strips to the underside of the Darco. The...
|
Forum: Repairs & Maintenance
12-06-2019, 01:47 AM
|
Replies: 66
Views: 28,786
Hi Sourdough
My earlier response was not meant...
Hi Sourdough
My earlier response was not meant to be a rant rather more to inform prospective buyers that the same frame problems still exist and now new issues like Darco are appearing. I wish I...
|
Forum: Repairs & Maintenance
12-03-2019, 12:04 PM
|
Replies: 66
Views: 28,786
|
Forum: Repairs & Maintenance
12-03-2019, 04:23 AM
|
Replies: 66
Views: 28,786
|
Forum: Fifth Wheels
11-08-2019, 03:36 AM
|
Replies: 18
Views: 34,438
I recently noticed that the Darco was showing...
I recently noticed that the Darco was showing signs of impending damage. I countersunk-screwed 2" strips of 3/16" UHMW sheet about every foot and a 6" wide one in the slide centre.
Slide now moves a...
|
Forum: Repairs & Maintenance
11-06-2019, 04:16 AM
|
Replies: 10
Views: 2,035
|
Forum: Repairs & Maintenance
11-04-2019, 03:47 AM
|
Replies: 10
Views: 8,834
Thanks for your reply SaskJames.
Way to go! -...
Thanks for your reply SaskJames.
Way to go! - I haven't thought of going through the floor as would have to remove bed slide. But much stronger result so will do.
I assume you welded the new frame...
|
Forum: Repairs & Maintenance
11-03-2019, 11:05 AM
|
Replies: 10
Views: 8,834
|
Forum: Repairs & Maintenance
10-04-2019, 02:42 PM
|
Replies: 10
Views: 8,834
Thanks for sharing.
Disappointing to see this...
Thanks for sharing.
Disappointing to see this continually happening. I thought youhave better consumer protection over there. We hit large pot holes & had some minor damage inside. I dropped the ...
|
Forum: Repairs & Maintenance
09-04-2019, 03:07 AM
|
Replies: 17
Views: 9,901
|
Forum: Repairs & Maintenance
08-25-2019, 05:40 AM
|
Replies: 4
Views: 1,719
Thanks John.
Unfortunately the years are...
Thanks John.
Unfortunately the years are catching me too but there's no-one in my state that do this work & usually a $A10,000 bill if a welding repair is needed whilst travelling.
I dropped the...
|